Scan Tool Data: TCM
WARNING: This page is about a different variant/trim than selected.
As the data values given in the following table are standard values estimated on the basis of values obtained from the normally operating vehicles by using a scan tool, use them as reference values. Even when the vehicle is in good condition, there may be cases where the checked value does not fall within each specified data range. Therefore, judgment as abnormal should not be made by checking with these data alone.
Also, condition in the following table that can be checked by the scan tool are those detected by TCM and output from TCM as commands and there may be cases where the CVT or actuator is not operating (in the condition) as indicated by the scan tool.
NOTE:
The following scan tool data related to CVT can be checked only by communicating with TCM.
SYMPTOM DIAGNOSIS DESCRIPTION CHART
| Scan tool data | Vehicle condition | Normal condition/reference values |
|---|---|---|
| Vehicle Speed see Scan Tool Data Definitions | Vehicle: Running | Value as same as speedometer reading |
| Engine Speed see Scan Tool Data Definitions |
|
650 RPM |
| Primary Pulley Speed see Scan Tool Data Definitions | Vehicle: Stop | 0 RPM |
| Lock-up: On | Value as same as engine speed | |
| Secondary Pulley Speed see Scan Tool Data Definitions | Vehicle: Stop | 0 RPM |
| Vehicle: Running at 40 km/h (25 mile/h) | 2000 RPM | |
| Torque converter Slip see Scan Tool Data Definitions |
|
Approx. 127 RPM |
| Primary Oil Pres see Scan Tool Data Definitions |
|
Approx. 1.0 MPa |
| Secondary Oil Pres see Scan Tool Data Definitions |
|
Approx. 1.0 MPa |
| CVTF Temperature see Scan Tool Data Definitions | After driving the vehicle, the temperature around CVT fluid temperature sensor reaches | 70 - 80 °C (158 - 176 °F) 70 - 80 °C (158 - 176 °F) |
| ECT see Scan Tool Data Definitions | Engine: Specified idle speed after warming up | 80 to 110 °C (176 to 230 °F) |
| Battery Voltage see Scan Tool Data Definitions | Engine: Specified idle speed | 13 to 15 V |
| Throttle position see Scan Tool Data Definitions |
|
0 to 5% |
|
90 to 100% | |
| Accel Actual Position see Scan Tool Data Definitions |
|
0 to 10% |
|
90 to 100% | |
| Gear Actual Ratio see Scan Tool Data Definitions | Vehicle: Running | 0.40 - 2.34 |
| Lock Up Solenoid (Com) see Scan Tool Data Definitions |
|
Approx. 200 mA |
|
Approx. 500 mA | |
| Lock Up Solenoid (Mon) see Scan Tool Data Definitions |
|
Approx. 200 mA |
|
Approx. 500 mA | |
| Line Press Solenoid (Com) see Scan Tool Data Definitions |
|
Approx. 700 mA |
|
Approx. 200 mA | |
| Line Press Solenoid (Mon) see Scan Tool Data Definitions |
|
Approx. 700 mA |
|
Approx. 200 mA | |
| Secondary Solenoid (Com) see Scan Tool Data Definitions |
|
Approx. 600 mA |
|
Approx. 200 mA | |
| Secondary Solenoid (Mon) see Scan Tool Data Definitions |
|
Approx. 700 mA |
|
Approx. 200 mA | |
| Torque Converter Clutch see Scan Tool Data Definitions | Lock-up: Off | Release |
| Lock-up: Off ↔ On | Slip | |
| Lock-up: On | Connect | |
| Manual Gear Position see Scan Tool Data Definitions | Select lever: other than "M" range | deactive |
|
1st | |
|
2nd | |
|
3rd | |
|
4th | |
|
5th | |
|
6th | |
| Shift Down SW see Scan Tool Data Definitions | Select lever: "-" position | ON |
| Other than above condition | OFF | |
| Shift Up SW see Scan Tool Data Definitions | Select lever: "+" position | ON |
| Other than above condition | OFF | |
| Manual Mode SW see Scan Tool Data Definitions | Select lever: "M" range | ON |
| Other than above condition | OFF | |
| Transaxle Range see Scan Tool Data Definitions | Select lever is in "P" position | P |
| Select lever is in "R" position | R | |
| Select lever is in "N" position | N | |
| Select lever is in "D" position | D | |
| ABS Active see Scan Tool Data Definitions | ABS operating | ON |
| ABS not operating | OFF | |
| A/C Comp Clutch see Scan Tool Data Definitions |
|
ON |
| Other than above condition | OFF | |
| Brake Switch see Scan Tool Data Definitions | Brake pedal: Depressed fully | ON |
| Brake pedal: Released | OFF | |
| Paddle Up SW see Scan Tool Data Definitions | Right side shift paddle "+": Pulled | ON |
| Right side shift paddle "+": Released | OFF | |
| Paddle Down SW see Scan Tool Data Definitions | Left side shift paddle "-": Pulled | ON |
| Left side shift paddle "-": Released | OFF | |
| Switching Solenoid (Mon) see Scan Tool Data Definitions | Select lever: "P" or "N" range | ON |
| Select lever: "D" or "R" range | OFF | |
| Switching Solenoid (Com) see Scan Tool Data Definitions | Select lever: "P" or "N" range | ON |
| Select lever: "D" or "R" range | OFF |