Transfer Case
- Motor - Shift Type (Transfer With Shift Actuator)
- Precautions
- General Description
- Transfer Description
- Transfer Shift Control System Components
- 4WD Control System Description
- Function of 4WD Control System Component
- 4WD Control System Operation
- 4WD Control System Wiring Circuit Diagram
- Terminal Arrangement of 4WD Control Module
- Input/Output Signal Table of 4WD Control Module
- On-Board Diagnostic System Description
- CAN Communication System Description
- Diagnostic Information And Procedure
- 4WD Control System Check
- Notes
- Detail of 4WD Control System Check
- Step 1: Customer complaint analysis
- Step 2. DTC/freeze frame data check, record and clearance
- Step 3 and 4. Visual inspection
- Step 5. Trouble symptom confirmation
- Step 6 and 7. Rechecking and record of DTC and freeze frame data
- Step 8. 4WD control symptom diagnosis
- Step 9. Troubleshooting for DTC
- Step 10. Check for intermittent problem
- Step 11. Final confirmation test
- Transfer Position Indicator Operation Check
- 4WD Control System Operation Inspection
- Visual Inspection
- DTC Check
- DTC Clearance
- DTC Table
- Fail-Safe Table
- Scan Tool Data
- Scan Tool Data Definitions
- 4WD Control Symptom Diagnosis
- Transfer Position Indicator Does Not Come ON at Ignition Switch ON but Engine Stops
- Transfer Position Indicator Remains ON Steady at Ignition Switch ON
- DTC C1213: Transfer Switch Circuit Open
- DTC C1214: Transfer Switch Circuit Short
- DTC C1223/C1235: Transfer Shift Actuator Motor Position Switch 1 Circuit Open/Transfer Shift Actuator Motor Position Switch 2 Circuit Open
- DTC C1224/C1236: Transfer Shift Actuator Motor Position Switch 1 Circuit Short/Transfer Shift Actuator Motor Position Switch 2 Circuit Short
- DTC C1227: 4L/N Switch Circuit Open
- DTC C1228: 4L/N Switch Circuit Short
- DTC C1230: Transfer Actuator Circuit Malfunction
- DTC C1237: Center Differential Lock Switch Circuit Open
- DTC C1238: Center Differential Lock Switch Circuit Short
- DTC C1240: 4WD Control Module Power Supply Circuit Malfunction
- DTC C1243: Internal Circuit Malfunction of 4WD Control Module
- DTC C1246: Clutch Pedal Position (CPP) Switch Circuit Short
- DTC U1073: Control Module Communication Bus Off
- DTC U1100: Lost Communication with ECM
- DTC U1101: Lost Communication with TCM
- DTC U1121: Lost Communication with ABS/Electronic Stability Program Hydraulic Unit/Control Module
- Inspection of 4WD Control Module and Its Circuits
- 4WD Control System Check
- Repair Instructions
- Transfer Oil Level Check
- Transfer Oil Change
- Transfer Oil Seal Removal and Installation
- Transfer Switch Removal and Installation
- Transfer Switch Inspection
- 4WD Control Module Removal and Installation
- Transfer Assembly Dismounting and Remounting
- Transfer Assembly Components
- Transfer Assembly Disassembly and Reassembly
- Transfer Assembly Inspection
- Input Gear Assembly, Counter Gear Assembly, Front Output Shaft Assembly and Rear Output Shaft Assembly Components
- Input Gear Assembly Disassembly and Reassembly
- Counter Gear Assembly Disassembly and Reassembly
- Front Output Shaft Assembly Disassembly and Reassembly
- Rear Output Shaft Assembly Disassembly and Reassembly
- Specifications
- Special Tools And Equipment
- Non-Shift Type (Transfer Without Shift Actuator)
- Precautions
- General Description
- Diagnostic Information And Procedures
- Repair Instructions
- Transfer Oil Change
- Transfer Oil Level Check
- Transfer Oil Seal Removal and Installation
- Transfer Assembly Dismounting and Remounting
- Transfer Assembly Components
- Transfer Assembly Disassembly and Reassembly
- Input Gear Assembly Disassembly and Reassembly
- Front Output Shaft Assembly Disassembly and Reassembly
- Rear Output Shaft Assembly Disassembly and Reassembly
- Specifications
- Special Tools And Equipment