LEMON Manuals: Even more car manuals for everyone
Home >> Suzuki >> 2003 >> Aerio S, Automatic >> Repair and Diagnosis >> Engine Performance >> System >> Engine Controls - Self-Diagnostics >> Diagnostic Tests >> DTC P0452: EVAP System Pressure Sensor - Low Input >> Diagnosis & Repair Procedure

Diagnosis & Repair Procedure

NOTE: For better performance and results of this diagnostic procedure, usage of appropriate wiring diagram is recommended. See ENGINE PERFORMANCE in SYSTEM WIRING DIAGRAMS article in ELECTRICAL.
NOTE: Perform all voltage and resistance tests using a Digital Volt-Ohmmeter (DVOM) with a minimum 10-megohm input impedance, unless stated otherwise in test procedure. Use an ohmmeter to isolate wiring harness shorts or opens.
  1. If engine system check has been performed, go to next step. If engine system check has not been performed, perform TEST D: ENGINE SYSTEM CHECK  under SYSTEM TESTS, then go to next step.
  2. Turn ignition switch to LOCK position. Remove fuel tank. See FUEL TANK under FUEL SYSTEM in REMOVAL & INSTALLATION article. Disconnect FTP sensor 4-pin harness connector L91. See Figure. Check FTP sensor and harness connector for poor, loose, corroded or damaged connector terminals. If connector terminals are faulty, repair as necessary and repeat DTC CONFIRMATION TEST . If connector terminals are okay, turn ignition switch to ON position and measure voltage between ground and FTP sensor connector L91 terminal No. 3 (Gray/Red wire). See Figure. If voltage is not 4-6 volts, go to next step. If voltage is 4-6 volts, go to step  6.
  3. Turn ignition switch to LOCK position. Remove ECM. See ENGINE CONTROL MODULE under COMPUTERIZED ENGINE CONTROLS in REMOVAL & INSTALLATION article. Check ECM and harness connectors for poor, loose, corroded or damaged connector terminals. If connector terminals are faulty, repair as necessary and repeat DTC CONFIRMATION TEST . If connector terminals are okay, reconnect ECM harness connectors and turn ignition switch to ON position. Backprobe and measure voltage between ground and ECM harness connector C46 terminal No. 18 (Gray/Red wire). See Figure. If voltage is not 4-6 volts, go to next step. If voltage is 4-6 volts, check for open circuit in Gray/Red wire between FTP sensor, Throttle Position (TP) sensor, Manifold Absolute Pressure (MAP) sensor and ECM. If no open circuit is found, go to next step. If open circuit is found, repair as necessary and repeat DTC CONFIRMATION TEST .
  4. Turn ignition switch to LOCK position. Disconnect TP sensor and MAP sensor harness connectors. See Figure. Turn ignition switch to ON position. Backprobe and measure voltage between ground and ECM harness connector C46 terminal No. 18 (Gray/Red wire). See Figure. If voltage is not 4-6 volts, go to next step. If voltage is 4-6 volts, check TP sensor and/or MAP sensor for malfunction referring to appropriate DTC test procedure. See DIAGNOSTIC TROUBLE CODE DEFINITIONS . After repair, repeat DTC CONFIRMATION TEST .
  5. Turn ignition switch to LOCK position. Measure resistance between ground and FTP sensor harness connector L91 terminal No. 3 (Gray/Red wire). See Figure. If resistance is infinity, go to next step. If any resistance is found, check for short to ground in Gray/Red wire between FTP sensor, TP sensor, MAP sensor and ECM. If short circuit is found, repair as necessary and repeat DTC CONFIRMATION TEST . If short circuit is not found, substitute ECM with a known good unit and repeat DTC CONFIRMATION TEST .
  6. Reconnect ECM harness connectors. Measure resistance between ground and FTP sensor harness connector L91 terminal No. 2 (Orange wire). See Figure. If resistance is 10 ohms or more, go to next step. If resistance is less than 10 ohms, go to step  8.
  7. Backprobe and measure resistance between ground and ECM harness connector G04 terminal No. 18 (Orange wire). See Figure. If resistance is less than 5 ohms, repair open or short circuit in Orange wire. After repair, repeat DTC CONFIRMATION TEST .If resistance is 5 ohms or more, check ECM ground circuits (Black/Orange wire) and (Black wire) for open or short circuit between ECM and ground. If ground circuits are faulty, repair as necessary and repeat DTC CONFIRMATION TEST . If ground circuits are okay, substitute ECM with a known good unit and repeat DTC CONFIRMATION TEST .
  8. Disconnect ECM harness connector G04. Turn ignition switch to LOCK position. Measure resistance between ground and ECM harness connector G04 terminal No. 33 (Red/Yellow wire). See Figure. If resistance is infinity, go to next step. If any resistance is found, repair short to ground in Red/Yellow wire between FTP sensor and ECM. After repair, repeat DTC CONFIRMATION TEST .
  9. Measure resistance between ECM harness connector G04 terminal No. 33 (Red/Yellow wire) and FTP sensor harness connector L91 terminal No. 1 (Red/Yellow wire). See Figure and Figure . If resistance is less than 5 ohms, go to next step. If resistance is 5 ohms or more, repair short circuit in Red/Yellow wire between FTP sensor and ECM. After repair, repeat DTC CONFIRMATION TEST .
  10. Perform FTP sensor component test. See FUEL TANK PRESSURE SENSOR under FUEL EVAPORATION under EMISSION SYSTEMS & SUB-SYSTEMS in SYSTEM & COMPONENT TESTING article. If FTP sensor is okay, substitute ECM with a known good unit and repeat DTC CONFIRMATION TEST . If FTP sensor is faulty, replace FTP sensor and repeat DTC CONFIRMATION TEST .
scientia non olet · About LEMON Manuals