LEMON Manuals: Even more car manuals for everyone
Home >> Subaru >> 2024 >> WRX Base >> Repair and Diagnosis >> Accessories & Equipment >> Exterior Lights >> Lighting System >> Headlight System >> Inspection >> Check Headlight System >> Model Without SRH

Model Without SRH

Wiring diagram: 

Headlight system Ref. to WIRING SYSTEM>HEADLIGHT SYSTEM>WIRING DIAGRAM .

G14612339Courtesy of SUBARU OF AMERICA, INC.
  1. CHECK HEADLIGHT ILLUMINATION  .
    1. Turn the ignition switch to ON.
    2. Turn the lighting switch to the switch 2 (HEAD) position and switch UP (HI) position.

    Does the headlight (low beam and high beam) come on?

    Yes:  The headlight system is normal.

    No:  Go to  2.

  2. CHECK DTC  .
    1. Turn the ignition switch to ON.
    2. Turn the lighting switch to the switch 2 (HEAD) position and switch UP (HI) position.
    3. Read the DTC of [Front Relay Control Module] using the Subaru Select Monitor. Ref. to COMMON (DIAGNOSTICS)>DIAGNOSTIC TROUBLE CODE (DTC) .

    Are any DTCs displayed?

    Yes:  Perform the diagnosis for the displayed DTCs. Ref. to FRONT RELAY CONTROL MODULE (DIAGNOSTICS)>DIAGNOSTIC TROUBLE CODE (DTC)>LIST .

    No:  Go to  3.

  3. CHECK POWER SUPPLY  .

    Using the Subaru Select Monitor, display the following items in the [Data monitor] of [Front Relay Control Module]. Ref. to COMMON (DIAGNOSTICS)>DATA MONITOR .

    • [BATT Voltage (Control)]
    • [BATT Voltage (BACKUP)]
    • [IGN Voltage]

    Is the voltage 9 - 16 V?

    Yes:  Go to  4.

    No:  Check the front relay control module and replace it if defective.

  4. PERFORM ACTIVE TEST  .

    Using the Subaru Select Monitor, check the following items in the [Active Test] of [Front Relay Control Module]. Ref. to FRONT RELAY CONTROL MODULE (DIAGNOSTICS)>ACTIVE TEST .

    NOTE: Check the items where illumination did not occur in step 1.
    • [Lighting Low RH Output]
    • [Lighting Low LH Output]
    • [Lighting High RH Output]
    • [Lighting High LH Output]

    Does the light illuminate?

    Yes:  Go to  9.

    No:  Go to  5.

  5. CHECK HEADLIGHT POWER SUPPLY CIRCUIT  .
    1. Turn the ignition switch to OFF.
    2. Disconnect the front relay control module connector.
    3. Measure the voltage between front relay control module connector and chassis ground.

      Connector & terminal 

      Headlight RH

      (B68) No. 1 (+) - Chassis ground (-):

      Headlight LH

      (B69) No. 6 (+) - Chassis ground (-):

    Is the voltage 9 - 16 V?

    Yes:  Go to  6.

    No:  Check the harness of the fuse, connector and power supply circuit. If there are no problems, replace the front relay control module. Ref. to BODY CONTROL/COMMUNICATION SYSTEM>FRONT RELAY CONTROL MODULE .

  6. CHECK HARNESS  .
    1. Disconnect the connector of the light which did not illuminate.
    2. Check the harness between the front relay control module and the headlight.

      Connector & terminal 

      Headlight RH (low beam)

      (B68) No. 2 - (B121) No. 1:

      Headlight RH (high beam) 

      (B69) No. 2 - (B121) No. 3:

      Headlight LH (low beam) 

      (B69) No. 8 - (B122) No. 1:

      Headlight LH (high beam) 

      (B69) No. 7 - (B122) No. 3:

    Is harness normal?

    Yes:  Go to  7.

    No:  Repair or replace the defective part.

  7. CHECK HEADLIGHT  .

    Apply battery voltage between headlight unit connector terminals.

    CAUTION: Make sure that the high beam illuminates because the high beam shares the same lighting body with the low beam and they are alternatively lit by switching. When applying battery voltage, do not mix up the positive (+) side and the negative (-) side. Incorrect polarity connection may cause internal LED damage.

    Connector & terminal 

    • If the low beam does not illuminate

      Headlight RH 

      (B121) No. 1 (+) - (B121) No. 2 (-):

      Headlight LH 

      (B122) No. 1 (+) - (B122) No. 2 (-): 

    • If the high beam does not illuminate 

      Headlight RH 

      (B121) No. 3 - (B121) No. 2 (-):

      Headlight LH 

      (B122) No. 3 - (B122) No. 2 (-):

    Does the headlight (low beam and high beam) come on at normal brightness?

    Yes:  Go to  8.

    No:  Replace the headlight assembly. Ref. to LIGHTING SYSTEM>HEADLIGHT ASSEMBLY .

  8. CHECK HARNESS  .

    Check the harness between the headlight connector and the chassis ground.

    Connector & terminal 

    Headlight RH 

    (B121) No. 2 - Chassis ground:

    Headlight LH 

    (B122) No. 2 - Chassis ground:

    Is harness normal?

    Yes:  Check the front relay control module and replace it if defective.

    No:  Repair or replace the defective part.

  9. CHECK CURRENT DATA  .
    1. Turn the ignition switch to ON.
    2. Using the Subaru Select Monitor, display the following items in the [Data monitor] of [Body Control]. Ref. to COMMON (DIAGNOSTICS)>DATA MONITOR .
      • [Lighting II Switch Input]
      • [Dimmer Hi Switch Input]

    Does the display change between [OFF] ←→ [ON] when the lighting switch is moved to the switch 2 (HEAD) and switch UP (HI) positions?

    Yes:  Go to  10.

    No:  Check the combination switch or harness for open circuit.

  10. CHECK CURRENT DATA  .
    1. Turn the ignition switch to ON.
    2. Using the Subaru Select Monitor, display the following items in the [Data monitor] of [Front Relay Control Module]. Ref. to COMMON (DIAGNOSTICS)>DATA MONITOR .
      • [Lighting Low Request]
      • [Lighting High Request]

    Does the display change to [ON] when turning the lighting switch to the switch 2 (HEAD) position and switch UP (HI) position?

    Yes:  Replace the front relay control module. Ref. to BODY CONTROL/COMMUNICATION SYSTEM>FRONT RELAY CONTROL MODULE .

    No:  Replace the body integrated unit. Ref. to BODY CONTROL/COMMUNICATION SYSTEM>BODY INTEGRATED UNIT .

scientia non olet · About LEMON Manuals