Basic Diagnostic Procedure: Procedure

WARNING: This page is about a different car, the 2022 Subaru WRX. However, it is still accessible from the selected car via links, so may be relevant.

CAUTION:

Subaru Select Monitor is required for reading DTC, performing diagnosis and reading data monitor.
Before removal or installation, be sure to remove any foreign matter (dust, moisture, oil, etc.).
Registration of immobilizer may be needed after the replacement of control modules, etc. For detailed procedure, refer to the "REGISTRATION MANUAL FOR IMMOBILIZER" provided as a separate volume.

NOTE:

Using the function setting (customizing), check that the keyless access system is not in a canceled state. Ref. to SECURITY AND LOCKS>FUNCTION SETTING (CUSTOMIZE)>OPERATION

PERFORM CUSTOMER INTERVIEW .
Ask the customer when and how the trouble occurred using the Check List for Interview. Ref. to KEYLESS ACCESS WITH PUSH BUTTON START (DIAGNOSTICS)>CHECK LIST FOR INTERVIEW

Did you interview the customer?

Yes : Go to 2.

No : Perform the interview, and Go to 2.
BASIC INSPECTION .
Perform basic inspection. Ref. to KEYLESS ACCESS WITH PUSH BUTTON START (DIAGNOSTICS)>GENERAL DESCRIPTION>INSPECTION

Is the check result OK?

Yes : Go to 3.

No : Repair the faulty part found in basic inspection, and Go to 3.
CHECK SUBARU SELECT MONITOR COMMUNICATION .
1. Turn the ignition switch to OFF.
2. Connect the Subaru Select Monitor to data link connector. Ref. to COMMON (DIAGNOSTICS)>DATA LINK CONNECTOR
3. Turn the ignition switch to ON and run the Subaru Select Monitor.
4. Select [Keyless Access with Push Button Start (Power Supply)] and [Keyless Access with Push Button Start (Collation)].
  NOTE:
  For detailed operation procedures, refer to "Help" of application.
Is communication possible?

Yes : Go to 4.

No : Check the communication circuit. Ref. to KEYLESS ACCESS WITH PUSH BUTTON START (DIAGNOSTICS)>DIAGNOSTIC PROCEDURE FOR SUBARU SELECT MONITOR COMMUNICATION>INSPECTION
CHECK DTC .
Using the Subaru Select Monitor, read the DTCs of [Keyless Access with Push Button Start (Power Supply)] and [Keyless Access with Push Button Start (Collation)]. Ref. to KEYLESS ACCESS WITH PUSH BUTTON START (DIAGNOSTICS)>DIAGNOSTIC TROUBLE CODE (DTC)
- Keyless Access with Push Button Start (Power Supply)
- Keyless Access with Push Button Start (Collation)
Are any DTCs displayed? (Current code)

Yes : Record the DTC, time stamp and freeze frame data, and Go to 5.

No : Go to 6.
PERFORM DIAGNOSIS .
1. Perform the diagnosis according to the DTC. Ref. to KEYLESS ACCESS WITH PUSH BUTTON START (DIAGNOSTICS)>DIAGNOSTIC TROUBLE CODE (DTC)>LIST
2. Repair or replace the cause of trouble.
3. Using the Subaru Select Monitor, perform the clear memory of [Keyless Access with Push Button Start (Power Supply)] and [Keyless Access with Push Button Start (Collation)]. Ref. to COMMON (DIAGNOSTICS)>CLEAR MEMORY
  - Keyless Access with Push Button Start (Power Supply)
  - Keyless Access with Push Button Start (Collation)
4. Execute the inspection mode. Ref. to KEYLESS ACCESS WITH PUSH BUTTON START (DIAGNOSTICS)>INSPECTION MODE
5. Using the Subaru Select Monitor, read the DTCs of [Keyless Access with Push Button Start (Power Supply)] and [Keyless Access with Push Button Start (Collation)]. Ref. to KEYLESS ACCESS WITH PUSH BUTTON START (DIAGNOSTICS)>DIAGNOSTIC TROUBLE CODE (DTC)
  - Keyless Access with Push Button Start (Power Supply)
  - Keyless Access with Push Button Start (Collation)
Are any DTCs displayed? (Current code)

Yes : Repeat step 5 until DTC is not shown. Go to 5.

No : Finish the diagnosis.
CHECK LIST OF DIAGNOSTICS WITH PHENOMENON .
Check "Diagnostics with Phenomenon". Ref. to KEYLESS ACCESS WITH PUSH BUTTON START (DIAGNOSTICS)>DIAGNOSTICS WITH PHENOMENON>LIST

Is there a corresponding symptom in the Diagnostics with Phenomenon?

Yes : Perform diagnosis according to the procedures in the diagnostics with phenomenon. Ref. to KEYLESS ACCESS WITH PUSH BUTTON START (DIAGNOSTICS)>DIAGNOSTICS WITH PHENOMENON>INSPECTION

No : Keyless access with push button start system is normal.