LEMON Manuals: Even more car manuals for everyone
Home >> Subaru >> 2021 >> Outback Base >> Repair and Diagnosis >> Transmission >> Automatic Trans >> CVT Transaxle System (Tr580) >> General Description >> Preparation Tool >> SUBARU Special Tool

SUBARU Special Tool

ILLUSTRATION TOOL NUMBER DESCRIPTION REMARKS
G05002948Courtesy of SUBARU OF AMERICA, INC.
 398177700 INSTALLER
  • Used to install the rear drive shaft ball bearing.
    NOTE: Used together with EXTENSION DRIVE SHAFT (927130000).
  • Used for installing the roller bearing of the secondary pulley side in the transmission case.
    NOTE: Used together with BUSHING 1-2 INSTALLER (499277100) and PRESS SNAP RING (28499TC010).
  • Used for installing the taper roller bearing (front) outer race of drive pinion retainer.
    NOTE: Used together with PRESS SNAP RING (28499TC010).
  • Used for installing the drive pinion retainer plug.
    NOTE: Used together with PRESS SNAP RING (499755602) and INSTALLER (899580100).
G05002437Courtesy of SUBARU OF AMERICA, INC.
 398437700 OIL SEAL INSTALLER Used for inspecting clutch clearance.
NOTE: Used together with GAUGE (499575600).
G05002462Courtesy of SUBARU OF AMERICA, INC.
 398497701 SEAT Used for removing and installing the side bearing inner race.
NOTE:
  • Used together with PULLER ASSY (399703600) when removing.
  • Used together with BUSHING 1-2 INSTALLER (499277100) when installing.
G05002431Courtesy of SUBARU OF AMERICA, INC.
 398527700 PULLER ASSY
  • Used for removing the roller bearing of the secondary pulley side in the transmission case.
    NOTE: Used together with CLAW (18760AA000).
  • Used for removing the taper roller bearing (front) outer race of drive pinion retainer, and taper roller bearing (rear) outer race.
  • Used for removing the drive pinion retainer oil seal.
G13591890Courtesy of SUBARU OF AMERICA, INC.
 398673600 COMPRESSOR Used for removing and installing snap ring of forward clutch.
NOTE: Used together with COMPRESSOR SPECIAL TOOL (18762AA010).
G05032458Courtesy of SUBARU OF AMERICA, INC.
 399703600 PULLER ASSY
  • Used for removing the parking gear.
  • Used for removing the side bearing inner race.
    NOTE: Used together with SEAT (398497701).
  • PULLER ASSY (399703601) can also be used.
G05002432Courtesy of SUBARU OF AMERICA, INC.
 498057300 OIL SEAL INSTALLER Used for installing the extension case oil seal.
G05002916Courtesy of SUBARU OF AMERICA, INC.
 498077300 REMOVER Used for removing the transfer drive gear ball bearing.
NOTE: Used together with INSTALLER (18657AA000).
G05002944Courtesy of SUBARU OF AMERICA, INC.
 498077400 REMOVER Used for removing the ball bearing of transfer driven gear.
NOTE: Used together with REMOVER (899864100).
G05002454Courtesy of SUBARU OF AMERICA, INC.
 498077600 REMOVER Used for removing the ball bearing of drive sprocket.
NOTE: Used together with HOUSING BUSHING INSTALLER AND REMOVER (927720000).
G05002439Courtesy of SUBARU OF AMERICA, INC.
 498255400 PLATE Used for measuring the backlash of the hypoid gear set.
G04997553Courtesy of SUBARU OF AMERICA, INC.
 498277200 STOPPER SET Used for removing and installing transmission body.
G07665421Courtesy of SUBARU OF AMERICA, INC.
 498497300 CRANKSHAFT STOPPER Used for removing and installing the drive plate.
G05343003Courtesy of SUBARU OF AMERICA, INC.
 498515500 REMOVER Used for removing the taper roller bearing (front) inner race of the drive pinion and drive pinion shim.
G05002425Courtesy of SUBARU OF AMERICA, INC.
 498575400 OIL PRESSURE GAUGE ASSY Used for measuring the transfer clutch pressure.
NOTE:
  • Used together with PRESSURE GAUGE ADAPTER (18681AA000).
  • Use the genuine O-ring (part No. 806908150) for installation.
G05002455Courtesy of SUBARU OF AMERICA, INC.
 498937110 HOLDER
  • Used for removing and installing the drive pinion lock nut.
    NOTE: Used together with ADAPTER (499787500) and WRENCH (499787700).
  • Used for adjusting hypoid gear set backlash.
    NOTE: Used together with WRENCH (499787700).
G05002445Courtesy of SUBARU OF AMERICA, INC.
 499267300 STOPPER PIN Used for adjusting the inhibitor switch.
G05002922Courtesy of SUBARU OF AMERICA, INC.
 499277100 BUSHING 1-2 INSTALLER
  • Used for installing the roller bearing of the secondary pulley side in the transmission case.
    NOTE: Used together with INSTALLER (398177700) and PRESS SNAP RING (28499TC010).
  • Used for installing the side bearing inner race.
    NOTE: Used together with SEAT (398497701).
G05022175Courtesy of SUBARU OF AMERICA, INC.
 499755602 PRESS SNAP RING Used for installing the drive pinion retainer plug.
NOTE: Used together with INSTALLER (398177700) and INSTALLER (899580100).
G05022173Courtesy of SUBARU OF AMERICA, INC.
 499575400 GAUGE
  • Used for adjusting the reduction drive gear shim.
  • Used for adjusting the primary pulley shim.
  • Used for adjusting the drive pinion washer.
  • Used for adjusting the drive pinion shim.
G06654336Courtesy of SUBARU OF AMERICA, INC.
 499575600 GAUGE
  • Used for adjusting the transfer driven gear shim.
  • Used for adjusting the transfer drive gear shim.
  • Used for adjusting the forward clutch washer.
  • Used for inspecting clutch clearance.
    NOTE: Used together with OIL SEAL INSTALLER (398437700).
G05002447Courtesy of SUBARU OF AMERICA, INC.
 499787500 ADAPTER Used for removing and installing the drive pinion lock nut.
NOTE: Used together with HOLDER (498937110) and WRENCH (499787700).
G05002446Courtesy of SUBARU OF AMERICA, INC.
 499787700 WRENCH
  • Used for removing and installing the drive pinion lock nut.
    NOTE: Used together with HOLDER (498937110) and ADAPTER (499787500).
  • Used for adjusting hypoid gear set backlash.
    NOTE: Used together with HOLDER (498937110).
G05002932Courtesy of SUBARU OF AMERICA, INC.
 499987003 SOCKET WRENCH (35) Used for removing and installing the lock nut of reduction driven gear.
NOTE: Used together with PULLEY WRENCH PIN SET (18334AA000) and PULLEY WRENCH (18355AA000).
G05002459Courtesy of SUBARU OF AMERICA, INC.
 899580100 INSTALLER
  • Used for installing the ball bearing of the transfer driven gear.
  • Used for installing the taper roller bearing (front) inner race of drive pinion.
    NOTE: Used together with EXTENSION DRIVE SHAFT (927130000).
  • Used for installing the drive pinion retainer plug.
    NOTE: Used together with INSTALLER (398177700) and PRESS SNAP RING (499755602).
G13950246Courtesy of SUBARU OF AMERICA, INC.
 899864100 REMOVER Used for removing the ball bearing of transfer driven gear.
NOTE: Used together with REMOVER (498077400).
G13950247Courtesy of SUBARU OF AMERICA, INC.
 899904100 STRAIGHT PIN REMOVER Used for removing the spring pin of the differential case.
G13950248Courtesy of SUBARU OF AMERICA, INC.
 927130000 EXTENSION DRIVE SHAFT
  • Used for installing the ball bearing of the transfer drive gear.
    NOTE: Used together with INSTALLER (398177700).
  • Used for installing the transfer drive gear.
  • Used for installing the parking gear.
  • Used for installing the taper roller bearing (front) inner race of drive pinion.
    NOTE: Used together with INSTALLER (899580100).
G13950249Courtesy of SUBARU OF AMERICA, INC.
 927720000 HOUSING BUSHING INSTALLER AND REMOVER
  • Used for installing the oil seal of the oil pump chain cover.
    NOTE: Use BUSHING SHAFT (927880000) and BASE TUBE LATERAL LINK (927890000).
  • Used for removing the ball bearing of drive sprocket.
    NOTE:
    • Use BUSHING SHAFT (927880000).
    • Used together with REMOVER (498077600).
  • Used for installing the drive pinion retainer oil seal.
    NOTE: Use BUSHING SHAFT (927880000).
G13950250Courtesy of SUBARU OF AMERICA, INC.
 16047AA000 LOCK PLATE Used for removing and installing the secondary pulley.
NOTE:
  • Used together with EXPANDER PULLEY (18769AA010).
  • When using together with EXPANDER PULLEY (18769AA010), EXPANDER PULLEY (18769AA030) is not necessary.
G13950251Courtesy of SUBARU OF AMERICA, INC.
 18270KA020 SOCKET (E20) Used for removing and installing the drive pinion retainer.
G13950252Courtesy of SUBARU OF AMERICA, INC.
 18334AA000 PULLEY WRENCH PIN SET Used for removing and installing the lock nut of reduction driven gear.
NOTE: Used together with SOCKET WRENCH (35) (499987003) and PULLEY WRENCH (18355AA000).
G13950253Courtesy of SUBARU OF AMERICA, INC.
 18351AA010 (Newly adopted tool) SLIDER
  • SHAFT
  • NUT
  • WEIGHT
  • Used for removing and installing snap ring of oil pump.
    NOTE:
    • Use only the shaft.
    • Used together with HOLDER (18361AA070), ADAPTER (18362AA080) and STANDASSY (18632AA040).
  • Used for removing oil pump.
    NOTE: Used together with ADAPTER (18362AA080).
G13950254Courtesy of SUBARU OF AMERICA, INC.
 18355AA000 PULLEY WRENCH Used for removing and installing the lock nut of reduction driven gear.
NOTE: Used together with SOCKET WRENCH (35) (499987003) and PULLEY WRENCH PIN SET (18334AA000).
G13950255Courtesy of SUBARU OF AMERICA, INC.
 18361AA070 (Newly adopted tool) HOLDER Used for removing and installing snap ring of oil pump.
NOTE: Used together with SLIDER (18351AA010), ADAPTER (18362AA080) and STANDASSY (18632AA040).
G13950256Courtesy of SUBARU OF AMERICA, INC.
 18362AA080 (Newly adopted tool) ADAPTER Used for removing and installing snap ring of oil pump.
NOTE: Used together with SLIDER (18351AA010), HOLDER (18361AA070) and STANDASSY (18632AA040).
G13950257Courtesy of SUBARU OF AMERICA, INC.
 18362AA090 (Newly adopted tool) ADAPTER Used for removing oil pump.
NOTE: Used together with SLIDER (18351AA010).
G13950258Courtesy of SUBARU OF AMERICA, INC.
 18460AA040 CHECK BOARD Used for measuring voltage and resistance of TCM terminals.
G13950259Courtesy of SUBARU OF AMERICA, INC.
 18632AA000 STAND ASSY Used for disassembling and assembling the transmission body.
G13950260Courtesy of SUBARU OF AMERICA, INC.
 18632AA040 (Newly adopted tool) STANDASSY Used for removing and installing snap ring of oil pump.
NOTE: Used together with SLIDER (18351AA010), HOLDER (18361AA070) and ADAPTER (18362AA080).
G13950261Courtesy of SUBARU OF AMERICA, INC.
 18657AA000 INSTALLER
  • Used for removing the transfer drive gear ball bearing.
    NOTE: Used together with REMOVER (498077300).
  • Used for installing the transmission case oil seal.
G13950262Courtesy of SUBARU OF AMERICA, INC.
 18658AA021 WRENCH COMPL RETAINER Used for removing and installing the differential side retainer.
G13950263Courtesy of SUBARU OF AMERICA, INC.
 18675AA000 DIFFERENTIAL SIDE OIL SEAL INSTALLER Used for installing the differential side retainer oil seal.
G13950264Courtesy of SUBARU OF AMERICA, INC.
 18681AA000 PRESSURE GAUGE ADAPTER Used for measuring the transfer clutch pressure.
NOTE:
  • Used together with OIL PRESSURE GAUGE ASSY (498575400).
  • Use the genuine O-ring (part No. 806911080) for installation.
G13950265Courtesy of SUBARU OF AMERICA, INC.
 18723AA000 REMOVER Used for removing the ball bearing of the rear drive shaft.
NOTE: Used together with BEARING REMOVER (18767AA010).
G13950266Courtesy of SUBARU OF AMERICA, INC.
 18760AA000 CLAW Used for removing the roller bearing of the secondary pulley side in the transmission case.
NOTE: Used together with PULLER ASSY (398527700).
G13950267Courtesy of SUBARU OF AMERICA, INC.
 18761AA010 SHEET SPECIAL TOOL Used for removing and installing valve cover.
NOTE: It is included in the control valve body for repairs.
G13950268Courtesy of SUBARU OF AMERICA, INC.
 18762AA001 COMPRESSOR SPECIAL TOOL
  • Used for removing and installing the transfer clutch piston.
  • Used for removing and installing the reverse brake piston.
  • COMPRESSOR SPECIAL TOOL (18762AA000) can also be used.
G13950269Courtesy of SUBARU OF AMERICA, INC.
 18762AA010 COMPRESSOR SPECIAL TOOL Used for removing and installing snap ring of forward clutch.
NOTE: Used together with COMPRESSOR (398673600).
G13950270Courtesy of SUBARU OF AMERICA, INC.
 18763AA000 COMPRESSOR SHAFT Used for adjusting hypoid gear set backlash.
G13950271Courtesy of SUBARU OF AMERICA, INC.
 18767AA000 BEARING REMOVER Used for removing the transfer drive gear.
G13950272Courtesy of SUBARU OF AMERICA, INC.
 18767AA010 BEARING REMOVER Used for removing the ball bearing of the rear drive shaft.
NOTE: Used together with REMOVER (18723AA000).
G13950273Courtesy of SUBARU OF AMERICA, INC.
 18769AA010 EXPANDER PULLEY Used for removing and installing the secondary pulley.
NOTE:
  • Used together with LOCK PLATE (16047AA000).
  • When using together with LOCK PLATE (16047AA000), the EXPANDER PULLEY (18769AA030) is not necessary.
G13950274Courtesy of SUBARU OF AMERICA, INC.
 18769AA030 EXPANDER PULLEY Used for removing and installing the secondary pulley.
NOTE: When using EXPANDER PULLEY (18769AA030), EXPANDER PULLEY (18769AA010) and LOCK PLATE (16047AA000) are not necessary.
G13950275Courtesy of SUBARU OF AMERICA, INC.
 18801AA000 OIL PRESSURE GAUGE ASSY Used for measuring the line pressure and secondary pressure.
NOTE: Use the genuine O-ring (part No. 806908150) for installation.
G13950276Courtesy of SUBARU OF AMERICA, INC.
 20099AE020 INSTALLER
  • Used for installing the drive sprocket ball bearing.
  • Used for installing the taper roller bearing (rear) outer race of drive pinion retainer.
G13950277Courtesy of SUBARU OF AMERICA, INC.
 28499TC010 PRESS SNAP RING
  • Used for installing the roller bearing of the secondary pulley side in the transmission case.
    NOTE: Used together with INSTALLER (398177700) and BUSHING 1-2 INSTALLER (499277100).
  • Used for installing the taper roller bearing (front) outer race of drive pinion retainer.
    NOTE: Used together with INSTALLER (398177700).
G13950278Courtesy of SUBARU OF AMERICA, INC.
 38415AA070 Axle shaft Used for measuring the hypoid gear set backlash and adjusting the thrust washer.
NOTE: This is the SUBARU genuine part.
G13950279Courtesy of SUBARU OF AMERICA, INC.
 41099AA012 ENGINE SUPPORT BRACKET Used for removing and installing transmission body.
NOTE: Used together with ENGINE SUPPORT (41099AA020).
G13950280Courtesy of SUBARU OF AMERICA, INC.
 41099AA020 ENGINE SUPPORT Used for removing and installing transmission body.
NOTE: Used together with ENGINE SUPPORT BRACKET (41099AA012).
G13950281Courtesy of SUBARU OF AMERICA, INC.
 - SUBARU SELECT MONITOR 4 Used for setting of each function and troubleshooting for electrical system.
NOTE:
  • For detailed operation procedures, refer to "Help" of application.
  • Used together with DST-i.
scientia non olet · About LEMON Manuals