Active Test: List

NOTE: Some items are not displayed according to destination area or vehicle equipment condition.

Active test item

Range

Contents

Execution condition

In-vehicle Air Temperature setting

-72.47 - 193.82°C

Set in-vehicle sensor readings. Adjusting the in-vehicle sensor value to use for A/C control is useful for reproduction test in faulty events.

Ignition switch ON

NOTE: Engine ON is recommended.

Ambient Air Temperature Setting

-40 - 80°C

Set ambient sensor readings. Adjusting the ambient sensor value to use for A/C control is useful for reproduction test in faulty events.

Ignition switch ON

NOTE: Engine ON is recommended.

Quantity of Sunload Setting

0 - 4448 W/m²

Set sunload sensor readings. Adjusting the sunload sensor value to use for A/C control is useful for reproduction test in faulty events.

Ignition switch ON

NOTE: Engine ON is recommended.

Heater Water Temperature Setting

-40 - 214°C

Set coolant temperature sensor readings. Adjusting the coolant temperature sensor value to use for A/C control is useful for reproduction test in faulty events.

Engine ON

AUTO switch mode setting

Transmit ON signal of AUTO switch contact. By operating A/C with the signal, it is possible to judge whether the control is faulty or the switch (center information display) is faulty.

Ignition switch ON

NOTE: Engine ON is recommended.

Air mix door actuator target open (driver's side)

-32.68 - 133.33 %

Set the driver's seat air mix door actuator opening angle. Useful for reproduction test in faulty events.

Ignition switch ON

NOTE: Engine ON is recommended.

Air mix door actuator target open (passenger's side)

-32.68 - 133.33 %

Set the passenger's seat air mix door actuator opening angle. Useful for reproduction test in faulty events.⁽¹⁾

Ignition switch ON

NOTE: Engine ON is recommended.

Fresh/Rec Air Dr Act Trgt Open Angle

-32.68 - 133.33 %

Set the intake door actuator opening angle. Useful for reproduction test in faulty events.

Ignition switch ON

NOTE: Engine ON is recommended.

Mode Door Actuator Opening Angle Target

-32.68 - 133.33 %

Set the mode door actuator opening angle. Useful for reproduction test in faulty events.

Ignition switch ON

NOTE: Engine ON is recommended.

Blower Fan Level Setting

0 - 255

NOTE: Input up to 255 is possible, but 100 - 255 is the same.

Set the blower fan level. Useful for reproduction test in faulty events.

Ignition switch ON

NOTE:

Engine ON is recommended.
Compressor OFF is needed to set the level to 0.

A/C Change Setting

ON/OFF

Set the compressor operation request. Useful for reproduction test in faulty events.

Engine ON
Blower ON

Rear Defogger Setting

ON/OFF

Transmit the rear defogger switch contact signal. By operating A/C with the signal, it is possible to judge whether the control is faulty or the switch (center information display) is faulty.

Ignition switch ON

NOTE: Engine ON is recommended.

Variable Flow Change Solenoid Duty

0 - 100%

Set Duty value of variable flow change solenoid valve. Useful for reproduction test in faulty events.

NOTE: The setting value may not be obtained due to A/C circuit protection.

Engine ON
Compressor ON
Blower ON

PTC steps

0 - 3

Set PTC level. Useful for reproduction test in faulty events.⁽²⁾

NOTE: The setting value may not be obtained due to power supply circuit protection.

Engine ON
Blower ON

Heater core temperature setting

-40 - 214°C

Set the heater core sensor readings. Adjusting the heater core sensor value to use for A/C control is useful for reproduction test in faulty events.

Ignition switch ON

NOTE: Engine ON is recommended.

Humidity Setting

0 - 100%

Set humidity sensor readings. Adjusting the humidity sensor value to use for A/C control is useful for reproduction test in faulty events.⁽³⁾

Ignition switch ON

NOTE: Engine ON is recommended.

⁽¹⁾	With left/right independent air conditioning function

⁽²⁾	With PTC heater

⁽³⁾	With humidity sensor