LEMON Manuals: Even more car manuals for everyone
Home >> Subaru >> 2021 >> Crosstrek Base, Standard Trans >> Repair and Diagnosis >> Electrical >> Gauges >> Instrumentation System (Diagnostics) >> Control Module I/O Signal >> Electrical Specification

Electrical Specification

G11264441Courtesy of SUBARU OF AMERICA, INC.
Terminal No. Contents Measuring condition Standard
(i10) No. 1 (+) ←→ Chassis ground (-) Battery power supply Always 8 - 16 V
(i10) No. 2 (+) ←→ Chassis ground (-) Ignition power supply (main) Ignition switch ON 8 - 16 V
(i10) No. 3 - - -
(i10) No. 4 (+) ←→ Chassis ground (-) Seat belt (driver's seat) Seat belt not fastened → fastened 8 - 16 V → 0 V
(i10) No. 5 - - -
(i10) No. 6 CAN H (CAN communication line) - -
(i10) No. 7 CAN L (CAN communication line) - -
(i10) No. 8 - - -
(i10) No. 9 - - -
(i10) No. 10 - - -
(i10) No. 11 MFD (UART communication line) (except for hybrid model) - -
(i10) No. 12 WARNING BOX (UART communication line) - -
(i10) No. 13 - - -
(i10) No. 14 Washer fluid level sensor Washer fluid level sensor OFF → ON 8 - 16 V → 0 V
(i10) No. 15 - - -
(i10) No. 16 - - -
(i10) No. 17 - - -
(i10) No. 18 Oil pressure warning light Oil pressure sensor OFF → ON 8 - 16 V → 0 V
(i10) No. 19 Security indicator - -
(i10) No. 20 - - -
(i10) No. 21 RH turn indicator - -
(i10) No. 22 LH turn indicator - -
(i10) No. 23 ←→ (i10) No. 24 Ambient sensor (+) Always Ref. to AIR CONDITIONER (EXCEPT FOR HEV)>AMBIENT SENSOR>INSPECTION .
(i10) No. 24 Ambient sensor (-) - -
(i10) No. 25 ←→ (i10) No. 26 Fuel level sensor (+) Always Ref. to FUEL INJECTION (FUEL SYSTEMS) (H4DO (EXCEPT FOR HEV))>FUEL LEVEL SENSOR>INSPECTION . Ref. to FUEL INJECTION (FUEL SYSTEMS) (H4DO(HEV))>FUEL LEVEL SENSOR>INSPECTION .
(i10) No. 26 Fuel level sensor (-) - -
(i10) No. 27 Select lever (UART communication line) - -
(i10) No. 28 - - -
(i10) No. 29 Illumination control switch (GND) - -
(i10) No. 30 Illumination control switch (VR) - -
(i10) No. 31 Illumination control switch (+) - -
(i10) No. 32 ←→ (i10) No. 29 Bright switch signal input Switch ON Continuity exists
(i10) No. 33 Bright switch signal output - -
(i10) No. 34 Illumi. (-) PWM - -
(i10) No. 35 SI-DRIVE switch (only for models with SI-DRIVE) - -
(i10) No. 36 ←→ Chassis ground Auto Start Stop OFF switch (only for models with Auto Start Stop) Switch ON Continuity exists
(i10) No. 37 ←→ Chassis ground X mode switch Switch ON Continuity exists
(i10) No. 38 ←→ Chassis ground TFT switch (TFT color meter only) Switch ON Continuity exists
(i10) No. 39 - - -
(i10) No. 40 ←→ Chassis ground GND Always Less than 1 Ω