LEMON Manuals: Even more car manuals for everyone
Home >> Subaru >> 2020 >> Outback Base >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Anti-Theft Systems >> Security And Locks - Keyless Access (W/Push Button Start) (Diagnostics) >> Diagnostics with Phenomenon >> Inspection >> Interior Collation Does Not Function

Interior Collation Does Not Function

Trouble causes: 

CAUTION:
  1. CHECK ACCESS KEY  .

    Check the battery of the access key. Refer to SECURITY AND LOCKS>Access Key>INSPECTION .

    Is the check result OK?

    Yes:  Go to  2.

    No  : Replace the battery.

  2. CHECK POWER SUPPLY CIRCUIT  .
    1. Disconnect the keyless access Control Module connector.
    2. Using a tester, measure the voltage between the keyless access Control Module connector and chassis ground.

    Connector & terminal 

    (i91) No. 4 (+) - Chassis ground (-):

    (i91) No. 1 (+) - Chassis ground (-):

    Is the voltage 9.5 - 16 V?

    Yes:  Go to  3.

    No  : Check the power supply circuit.

  3. CHECK INTERIOR ANTENNA (FRONT)  .
    1. Using the Subaru Select Monitor, check the following items in the [Keyless Access with Push Button Start Check] of [Keyless Access with Push Button Start(Collation)]. Refer to KEYLESS ACCESS WITH PUSH BUTTON START SYSTEM (DIAGNOSTICS)>KEYLESS ACCESS WITH PUSH BUTTON START CHECK .
      • Fr internal transmitter - internal tuner
    2. Using a tester, check the output between keyless access Control Module connector terminals while performing [Keyless Access with Push Button Start].

    Connector & terminal 

    (i92) No. 25 - (i92) No. 12:

    Is a pulse output?

    Yes:  Go to  4.

    No  : Replace the keyless access Control Module. Refer to SECURITY AND LOCKS>KEYLESS ACCESS Control Module .

  4. CHECK INTERIOR ANTENNA (CENTER)  .
    1. Using the Subaru Select Monitor, check the following items in the [Keyless Access with Push Button Start Check] of [Keyless Access with Push Button Start(Collation)]. Refer to KEYLESS ACCESS WITH PUSH BUTTON START SYSTEM (DIAGNOSTICS)>KEYLESS ACCESS WITH PUSH BUTTON START CHECK .
      • Rr internal transmitter - internal tuner
    2. Using a tester, check the output between keyless access Control Module connector terminals while performing [Keyless Access with Push Button Start].

    Connector & terminal 

    (i92) No. 9 - (i92) No. 3:

    Is a pulse output?

    Yes:  Go to  5.

    No  : Replace the keyless access Control Module. Refer to SECURITY AND LOCKS>KEYLESS ACCESS Control Module .

  5. CHECK INTERIOR ANTENNA (REAR)  .
    1. Using the Subaru Select Monitor, check the following items in the [Keyless Access with Push Button Start Check] of [Keyless Access with Push Button Start(Collation)]. Refer to KEYLESS ACCESS WITH PUSH BUTTON START SYSTEM (DIAGNOSTICS)>KEYLESS ACCESS WITH PUSH BUTTON START CHECK .
      • Trunk-internal transmitter - trunk-internal tuner or
      • R gate internal transmitter - internal tuner
    2. Using a tester, check the output between keyless access Control Module connector terminals while performing [Keyless Access with Push Button Start].

    Connector & terminal 

    (i92) No. 2 - (i92) No. 1:

    Is a pulse output?

    Yes:  Go to  6.

    No  : Replace the keyless access Control Module. Refer to SECURITY AND LOCKS>KEYLESS ACCESS Control Module .

  6. CHECK HARNESS (OPEN CIRCUIT)  .
    1. Disconnect the front interior antenna connector and the keyless access Control Module connector.
    2. Using a tester, check continuity between the front interior antenna connector and the keyless access Control Module connector.

    Connector & terminal 

    (i92) No. 25 - (i153) No. 1:

    (i92) No. 12 - (i153) No. 3:

    Is there continuity?

    Yes:  Go to  7.

    No  : Repair or replace the open circuit of harness.

  7. CHECK HARNESS (OPEN CIRCUIT)  .
    1. Disconnect the center interior antenna connector and the keyless access Control Module connector.
    2. Using a tester, check continuity between the center interior antenna connector and the keyless access Control Module connector.

    Connector & terminal 

    (i92) No. 9 - (L104) No. 1:

    (i92) No. 3 - (L104) No. 3:

    Is there continuity?

    Yes:  Go to  8.

    No  : Repair or replace the open circuit of harness.

  8. CHECK HARNESS (OPEN CIRCUIT)  .
    1. Disconnect the rear interior antenna connector and the keyless access Control Module connector.
    2. Using a tester, check continuity between the rear interior antenna connector and the keyless access Control Module connector.

    Connector & terminal 

    (i92) No. 2 - (L105) No. 1:

    (i92) No. 1 - (L105) No. 3:

    Is there continuity?

    Yes:  Go to  9.

    No  : Repair or replace the open circuit of harness.

  9. CHECK ANTENNA  .

    Replace the front interior antenna with a new or properly functioning part.

    Does it operate properly?

    Yes:  Replace the front interior antenna. Refer to SECURITY AND LOCKS>Keyless Access Indoor Antenna>REMOVAL .

    No  : Go to  10.

  10. CHECK ANTENNA  .

    Replace the center interior antenna with a new or properly functioning part.

    Does it operate properly?

    Yes:  Replace the center interior antenna. Refer to SECURITY AND LOCKS>Keyless Access Indoor Antenna>REMOVAL .

    No  : Go to  11.

  11. CHECK ANTENNA  .

    Replace the rear interior antenna with a new or properly functioning part.

    Does it operate properly?

    Yes:  Replace the rear interior antenna. Refer to SECURITY AND LOCKS>Keyless Access Indoor Antenna>REMOVAL .

    No  : Go to  12.

  12. CHECK KEYLESS ACCESS SYSTEM CHECK  .
    1. Using the Subaru Select Monitor, check the following items in the [Keyless Access with Push Button Start Check] of [Keyless Access with Push Button Start(Collation)]. Refer to KEYLESS ACCESS WITH PUSH BUTTON START SYSTEM (DIAGNOSTICS)>KEYLESS ACCESS WITH PUSH BUTTON START CHECK .
      • Fr internal transmitter - internal tuner
    2. Hold the access key 1 m or more away from the center console, then come closer to within 0.8 m.

    Does the buzzer sound?

    Yes:  Go to  13.

    No  : Replace the keyless access Control Module. Refer to SECURITY AND LOCKS>KEYLESS ACCESS Control Module .

  13. CHECK KEYLESS ACCESS SYSTEM CHECK  .
    1. Using the Subaru Select Monitor, check the following items in the [Keyless Access with Push Button Start Check] of [Keyless Access with Push Button Start(Collation)]. Refer to KEYLESS ACCESS WITH PUSH BUTTON START SYSTEM (DIAGNOSTICS)>KEYLESS ACCESS WITH PUSH BUTTON START CHECK .
      • Rr internal transmitter - internal tuner
    2. Hold the access key 1 m or more away from the center of the second-row seats, then come closer to within 0.8 m.

    Does the buzzer sound?

    Yes:  Go to  14.

    No  : Replace the keyless access Control Module. Refer to SECURITY AND LOCKS>KEYLESS ACCESS Control Module .

  14. CHECK KEYLESS ACCESS SYSTEM CHECK  .
    1. Using the Subaru Select Monitor, check the following items in the [Keyless Access with Push Button Start Check] of [Keyless Access with Push Button Start(Collation)]. Refer to KEYLESS ACCESS WITH PUSH BUTTON START SYSTEM (DIAGNOSTICS)>KEYLESS ACCESS WITH PUSH BUTTON START CHECK .
      • Trunk-internal transmitter - trunk-internal tuner

        or

      • R gate internal transmitter - internal tuner
    2. Hold the access key 1 m or more away from the back of the rear seat, then come closer to within 0.8 m.

    Does the buzzer sound?

    Yes:  The circuit has returned to a normal condition at this time. Reproduce the failure, and then perform the diagnosis again.

    NOTE: In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.

    No  : Replace the keyless access Control Module. Refer to SECURITY AND LOCKS>KEYLESS ACCESS Control Module .

scientia non olet · About LEMON Manuals