DTC P0172: System Too Rich Bank 1: Notes

1. -

DTC detecting condition:

Detected when two consecutive driving cycles with fault occur.

Trouble symptom:

Improper idling
Engine stall
Poor driving performance

NOTE: After the faulty parts are repaired or replaced, perform the final check in Basic Diagnostic Procedure. Ref. to ENGINE (DIAGNOSTICS) (H4DO)>BASIC DIAGNOSTIC PROCEDURE>PROCEDURE .

CHECK EXHAUST SYSTEM .
Check exhaust system parts.

Are there holes or loose bolts on exhaust system?

Yes: Repair the exhaust system.

No: Go to 2 .
CHECK AIR INTAKE SYSTEM .
Check the installing condition of the air intake system.

Are there holes, loose bolts or disconnection of hose on air intake system?

Yes: Repair the air intake system.

No: Go to 3 .
CHECK FUEL PRESSURE .
WARNING: Place "NO OPEN FLAMES" signs near the working area.
CAUTION:
- Be careful not to spill fuel.
- Before attaching/detaching a fuel pressure gauge, release the fuel pressure.
Measure the fuel pressure. Ref. to MECHANICAL (H4DO)>FUEL PRESSURE>INSPECTION .

Is the measured value 350 - 450 kPa (3.5 - 4.6 kg/cm² , 50 - 66 psi)?

Yes: Go to 4 .

No: Check the fuel pump and fuel delivery line. Ref. to FUEL INJECTION (FUEL SYSTEMS) (H4DO)>FUEL PUMP>INSPECTION . Ref. to FUEL INJECTION (FUEL SYSTEMS) (H4DO)>FUEL DELIVERY AND EVAPORATION LINES>INSPECTION .
CHECK ENGINE COOLANT TEMPERATURE SENSOR (OUTLET) .
1. Start the engine and warm up completely.
2. Using the Subaru Select Monitor, read the value in [Engine Coolant Temperature 1].
  NOTE: For detailed operation procedures, refer to "Common (Diagnostics)". Ref. to COMMON(DIAG)>DATA MONITOR .
Is the value of [Engine Coolant Temperature 1] 75°C (167°F) or more?

Yes: Go to 5 .

No: Replace the engine coolant temperature sensor (outlet). Ref. to FUEL INJECTION (FUEL SYSTEMS) (H4DO)>ENGINE COOLANT TEMPERATURE SENSOR .
CHECK MASS AIR FLOW AND INTAKE AIR TEMPERATURE SENSOR .
1. Start the engine and warm up until the engine coolant temperature exceeds 75°C (167°F).
2. Place the select lever in "P" range or "N" range.
3. Turn the A/C switch to OFF.
4. Turn all the accessory switches to OFF.
5. Using the Subaru Select Monitor, read the value in [Mass Air Flow].
  NOTE: For detailed operation procedures, refer to "Common (Diagnostics)". Ref. to COMMON(DIAG)>DATA MONITOR .
Is the value of [Mass Air Flow] 2 - 5 g/s (0.26 - 0.66 lb/m)?

Yes: Go to 6 .

No: Replace the mass air flow and intake air temperature sensor. Ref. to FUEL INJECTION (FUEL SYSTEMS) (H4DO)>MASS AIR FLOW AND INTAKE AIR TEMPERATURE SENSOR .
CHECK MASS AIR FLOW AND INTAKE AIR TEMPERATURE SENSOR .
1. Start the engine and warm up until the engine coolant temperature exceeds 75°C (167°F).
2. Place the select lever in "P" range or "N" range.
3. Turn the A/C switch to OFF.
4. Turn all the accessory switches to OFF.
5. Open the front hood.
6. Measure the ambient temperature.
7. Using the Subaru Select Monitor, read the value in [Intake Air Temp.].
  NOTE: For detailed operation procedures, refer to "Common (Diagnostics)". Ref. to COMMON(DIAG)>DATA MONITOR .
Subtract ambient temperature from [Intake Air Temp.]. Is the obtained value -10 - 50°C (-18 - 90°F)?

Yes: Go to 7 .

No: Check the mass air flow and intake air temperature sensor. Ref. to FUEL INJECTION (FUEL SYSTEMS) (H4DO)>MASS AIR FLOW AND INTAKE AIR TEMPERATURE SENSOR .
CHECK PCV VALVE .
Check the PCV valve. Ref. to EMISSION CONTROL (AUX. EMISSION CONTROL DEVICES) (H4DO)>PCV VALVE>INSPECTION .

Does the PCV valve have deformation, cracks or other damages?

Yes: Replace the PCV valve. Ref. to EMISSION CONTROL (AUX. EMISSION CONTROL DEVICES) (H4DO)>PCV VALVE .

No: Go to 8 .
CHECK PCV HOSE .
Check the PCV hose. Ref. to EMISSION CONTROL (AUX. EMISSION CONTROL DEVICES) (H4DO)>PCV HOSE>INSPECTION .

Does the PCV hose have deformation, cracks or other damages?

Yes: Replace the PCV hose. Ref. to EMISSION CONTROL (AUX. EMISSION CONTROL DEVICES) (H4DO)>PCV HOSE .

No: Repair the poor contact of ECM connector.