LEMON Manuals: Even more car manuals for everyone
Home >> Subaru >> 2019 >> Ascent Base >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Anti-Theft Systems >> Security And Locks - Keyless Access (W/Push Button Start) (Diagnostics) >> Basic Diagnostic Procedure >> Procedure

Basic Diagnostic Procedure: Procedure

CAUTION:
  • Subaru Select Monitor kit is required for reading DTC, performing diagnosis and reading data monitor.
  • Before removal or installation, be sure to remove any foreign matter (dust, moisture, oil, etc.).
  • Registration of immobilizer may be needed after the replacement of control modules, etc. For detailed procedure, refer to the "REGISTRATION MANUAL FOR IMMOBILIZER" provided as a separate volume.
NOTE: Using the Function Setting (Customize), check that the keyless access system is not in a cancelled state. Ref. to SECURITY AND LOCKS>FUNCTION SETTING (CUSTOMIZE)>OPERATION .
  1. PERFORM CUSTOMER INTERVIEW. 

    Ask the customer when and how the trouble occurred using the interview check list. Ref. to KEYLESS ACCESS WITH PUSH BUTTON START (DIAGNOSTICS)>CHECK LIST FOR INTERVIEW .

    Did you interview the customer?

    Yes  : Go to  2.

    No  : Perform the interview, and Go to  2.

  2. BASIC INSPECTION. 

    Perform basic inspection. Ref. to KEYLESS ACCESS WITH PUSH BUTTON START (DIAGNOSTICS)>GENERAL DESCRIPTION>INSPECTION .

    Is the check result OK?

    Yes  : Go to  3.

    No  : Repair the faulty part found in basic inspection, and Go to  3.

  3. CHECK SUBARU SELECT MONITOR COMMUNICATION. 
    1. Turn the ignition switch to OFF.
    2. Connect the Subaru Select Monitor to data link connector. Ref. to COMMON (DIAG)>DATA LINK CONNECTOR .
    3. Turn the ignition switch to ON and run the Subaru Select Monitor.
    4. Select keyless access with push button start.
      NOTE: For detailed operation procedures, refer to "Help" of application.

    Is communication possible?

    Yes  : Go to  4.

    No  : Check the communication circuit. Ref. to KEYLESS ACCESS WITH PUSH BUTTON START (DIAGNOSTICS)>DIAGNOSTIC PROCEDURE FOR SUBARU SELECT MONITOR COMMUNICATION .

  4. CHECK DTC. 

    Read the DTC of [Keyless Access with Push Button Start] using the Subaru Select Monitor. Ref. to KEYLESS ACCESS WITH PUSH BUTTON START (DIAGNOSTICS)>DIAGNOSTIC TROUBLE CODE (DTC) .

    Are any DTCs displayed? (Current malfunction)

    Yes  Record the DTC, time stamp and freeze frame data, and Go to  5.

    No  : Go to  6.

  5. PERFORM DIAGNOSIS. 
    1. Perform the diagnosis according to DTC.
    2. Repair or replace the cause of trouble.
    3. Using the Subaru Select Monitor, perform the clear memory of [Keyless Access with Push Button Start]. Ref. to COMMON (diag)>CLEAR MEMORY .
    4. Execute the inspection mode. Ref. to KEYLESS ACCESS WITH PUSH BUTTON START (DIAGNOSTICS)>INSPECTION MODE .
    5. Read the DTC of [Keyless Access with Push Button Start] using the Subaru Select Monitor. Ref. to KEYLESS ACCESS WITH PUSH BUTTON START (DIAGNOSTICS)>DIAGNOSTIC TROUBLE CODE (DTC) .

    Are any DTCs displayed? (Current malfunction)

    Yes  Repeat Go to  5. until DTC is not shown.

    No  : Finish the diagnosis.

  6. CHECK LIST OF DIAGNOSTICS WITH PHENOMENON. 

    Check "Diagnostics with Phenomenon". Ref. to KEYLESS ACCESS WITH PUSH BUTTON START (DIAGNOSTICS)>DIAGNOSTICS WITH PHENOMENON .

    Is there a symptom that corresponds in the phenomenon list?

    Yes  Perform diagnosis according to the procedures in the phenomenon list.

    No  : Keyless access with push button start system is normal.

scientia non olet · About LEMON Manuals