TX6A Automatic Transmission/Transaxle
SERVICE DATA
SERVICE DATA SPECIFICATIONS
| Line pressure (Fluid temperature): 50 to 80°C (122 to 176°F) Engine idling | D position | 350 to 430 kPa (3.6 to 4.4 kgf/cm2 , 51 to 62 psi) |
| R position | 760 to 950 kPa (7.7 to 9.7 kgf/cm2 , 110 to 138 psi) | |
| Line pressure (Fluid temperature): 50 to 80°C (122 to 176°F) At stall speed (Throttle valve fully open) | D position | 1200 to 1380 kPa (12.5 to 14.0 kgf/cm2 , 174 to 200 psi) |
| R position | 1410 to 1630 kPa (14.4 to 16.6 kgf/cm2 , 204 to 236 psi) | |
| Engine stall speed | D position | 2350 +/- 250 r/min |
| Time lag | N →D position | Less than 1.2 seconds |
| N →R position | Less than 1.5 seconds | |
| Drive plate runout | Maximum | 0.30 mm (0.0118 in.) |
SERVICE DATA (Automatic Transmission Unit:)
SERVICE DATA SPECIFICATIONS (AUTOMATIC TRANSMISSION UNIT)
| 1st and reverse return spring free length | Standard: 23.74 mm (0.935 in.) |
| Rear planetary gear pinion thrust clearance | Standard: 0.2 to 0.6 mm (0.00788 to 0.0236 in.) |
| Rear planetary gear bushing inside diameter | Standard: 18.025 mm (0.710 in.) |
| 1st and reverse brake pack clearance | 0.5 to 0.8 mm (0.0197 to 0.0315 in.) |
| Flange thickness (1st and reverse brake) | Mark 0: 0 mm (0 in.) Mark 1: 0.17 mm (0.00669 in.) Mark 3: 0.31 mm (0.0122 in.) Mark 4: 0.45 mm (0.0177 in.) Mark 5: 0.59 mm (0.0232 in.) Mark 7: 0.73 mm (0.0287 in.) Mark 8: 0.87 mm (0.0342 in.) Mark 10: 1.01 mm (0.0397 in.) Mark 11: 1.15 mm (0.0452 in.) Mark 12: 1.29 mm (0.0507 in.) |
| Intermediate shaft runout | Standard: 0.03 mm (0.00118 in.) |
| Intermediate shaft diameter | Standard A: 22.962 to 22.975 mm (0.9041 to 0.9045 in.) Standard B: 27.759 to 27.775 mm (1.0929 to 1.0935 in.) |
| Center planetary gear pinion thrust clearance | Standard: 0.12 to 0.68 mm (0.00473 to 0.0267 in.) |
| No. 2 brake pinion return spring free length | Standard: 22.66 mm (0.892 in.) |
| No. 2 brake piston piston stroke | 0.6 to 0.9 mm (0.0237 to 0.0354 in.) |
| Flange thickness (No. 2 brake piston) | Mark 0: 2.0 mm (0.0787 in.) Mark 1: 2.1 mm (0.0827 in.) Mark 2: 2.2 mm (0.0866 in.) Mark 3: 2.3 mm (0.0906 in.) Mark 4: 2.4 mm (0.0945 in.) Mark 5: 2.5 mm (0.0984 in.) Mark 6: 2.6 mm (0.102 in.) Mark 7: 2.7 mm (0.106 in.) |
| Brake piston return spring free length | Standard: 17.05 mm (0.671 in.) |
| Front planetary gear pinion thrust clearance | Standard: 0.20 to 0.60 mm (0.00788 to 0.0236 in.) |
| Front planetary gear bushing inside diameter | Standard: 48.78 mm (1.92 in.) |
| No. 1 brake piston piston stroke | 0.42 to 0.72 mm (0.0166 to 0.0283 in.) |
| No. 3 brake piston return spring free length | Standard: 15.72 mm (0.619 in.) |
| Flange thickness (No. 1 brake piston) | Mark 0: 2.0 mm (0.0787 in.) Mark 1: 2.2 mm (0.0866 in.) Mark 2: 2.4 mm (0.0945 in.) Mark 3: 2.6 mm (0.102 in.) |
SERVICE DATA (Clutch Drum And Input Shaft:)
SERVICE DATA SPECIFICATIONS (CLUTCH DRUM AND INPUT SHAFT)
| Direct clutch return spring free length | Standard: 20.02 mm (0.788 in.) |
| Reverse clutch return spring free length | Standard: 21.03 mm (0.828 in.) |
| Direct clutch pack clearance | 0.5 to 0.8 mm (0.0197 to 0.0314 in.) |
| Flange thickness (Direct clutch) | Mark 0: 3.0 mm (0.118 in.) Mark 1: 3.1 mm (0.122 in.) Mark 2: 3.2 mm (0.126 in.) Mark 3: 3.3 mm (0.130 in.) Mark 4: 3.4 mm (0.134 in.) Mark 5: 3.5 mm (0.138 in.) Mark 6: 3.6 mm (0.142 in.) Mark 7: 3.7 mm (0.146 in.) Mark 8: 3.8 mm (0.150 in.) |
| Reverse clutch pack clearance | 0.4 to 0.7 mm (0.0158 to 0.0275 in.) |
| Flange thickness (Reverse clutch) | Mark 0: 2.4 mm (0.0945 in.) Mark 1: 2.5 mm (0.0984 in.) Mark 2: 2.6 mm (0.102 in.) Mark 3: 2.7 mm (0.106 in.) Mark 4: 2.8 mm (0.110 in.) Mark 5: 2.9 mm (0.114 in.) Mark 6: 3.0 mm (0.118 in.) Mark 7: 3.1 mm (0.122 in.) Mark 8: 3.2 mm (0.126 in.) Mark 9: 3.3 mm (0.130 in.) Mark A: 3.4 mm (0.134 in.) Mark B: 3.5 mm (0.138 in.) |
| Forward clutch return spring free length | Standard: 26.29 mm (1.04 in.) |
| Forward clutch pack clearance | 0.56 to 0.86 mm (0.0221 to 0.0338 in.) |
| Flange thickness (Forward clutch) | Mark 0: 3.0 mm (0.118 in.) Mark 1: 3.1 mm (0.122 in.) Mark 2: 3.2 mm (0.126 in.) Mark 3: 3.3 mm (0.130 in.) Mark 4: 3.4 mm (0.134 in.) Mark 5: 3.5 mm (0.138 in.) Mark 6: 3.6 mm (0.142 in.) Mark 7: 3.7 mm (0.146 in.) Mark 8: 3.8 mm (0.150 in.) Mark 9: 3.9 mm (0.154 in.) |
| Coast clutch pack clearance | 0.4 to 0.7 mm (0.0158 to 0.0275 in.) |
| Flange thickness (Coast clutch) | Mark 0: 3.0 mm (0.118 in.) Mark 1: 3.1 mm (0.122 in.) Mark 2: 3.2 mm (0.126 in.) Mark 3: 3.3 mm (0.130 in.) Mark 4: 3.4 mm (0.134 in.) Mark 5: 3.5 mm (0.138 in.) Mark 6: 3.6 mm (0.142 in.) Mark 7: 3.7 mm (0.146 in.) Mark 8: 3.8 mm (0.150 in.) Mark 9: 3.9 mm (0.154 in.) |
| Forward clutch hub inside diameter | Standard: 23.037 to 23.062 mm (0.9070 to 0.9079 in.) |
| Reverse clutch hub inside diameter | Standard: 33.312 to 33.337 mm (1.3115 to 1.3125 in.) |
SERVICE DATA (Accumulator:)
SERVICE DATA SPECIFICATIONS (ACCUMULATOR)
| Spring | Free Length/Outer diameter mm (in.) | Color |
|---|---|---|
| B1 (Outer) | 46.36 (1.825)/17.10 (0.673) | Natural |
| C2 | 65.07 (2.562)/16.2 (0.638) | Pink |
| B3 | 70.5 (2.776)/19.7 (0.776) | Purple |
| C3 (Inner) | 44.0 (1.732)/14.0 (0.551) | Yellow |
| C3 (Outer) | 76.65 (3.0178)/20.10 (0.7913) | White |
SERVICE DATA (Output Shaft Bearing:)
SERVICE DATA SPECIFICATIONS (OUTPUT SHAFT BEARING)
| Clearance | 0.02 to 0.12 mm (0.000787 to 0.00472 in.) |
| Flange thickness | No. 1: 3.80 mm (0.150 in.) No. 2: 3.85 mm (0.152 in.) No. 3: 3.90 mm (0.154 in.) No. 4: 3.95 mm (0.156 in.) No. 5: 4.00 mm (0.157 in.) No. 6: 4.05 mm (0.159 in.) No. 7: 4.10 mm (0.161 in.) No. 8: 4.15 mm (0.163 in.) No. 9: 4.20 mm (0.165 in.) No. 10: 4.25 mm (0.167 in.) No. 11: 4.30 mm (0.169 in.) No. 12: 4.35 mm (0.171 in.) |