DTC Table

WARNING: This page is about a different car, the 2014 Subaru BRZ. However, it is still accessible from the selected car via links, so may be relevant.

DTC	Diagnostic items	Light on	Code recording
P000A	[A Camshaft Position Slow Response (Bank 1)]	◦	◦
P000B	[B Camshaft Position Slow Response (Bank 1)]	◦	◦
P000C	[A Camshaft Position Slow Response (Bank 2)]	◦	◦
P000D	[B Camshaft Position Slow Response (Bank 2)]	◦	◦
P0010	[A Camshaft Position Actuator Circuit/Open (Bank 1)]	◦	◦
P0011	[Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1)]	◦	◦
P0013	[B Camshaft Position - Actuator Circuit/Open (Bank 1)]	◦	◦
P0014	[Camshaft Position "B" - Timing Over-Advanced or System Performance (Bank 1)]	◦	◦
P0016	[Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A)]	◦	◦
P0017	[Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor B)]	◦	◦
P0018	[Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor A)]	◦	◦
P0019	[Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor B)]	◦	◦
P0020	[A Camshaft Position Actuator Circuit/Open (Bank 2)]	◦	◦
P0021	[Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 2)]	◦	◦
P0023	[B Camshaft Position - Actuator Circuit/Open (Bank 2)]	◦	◦
P0024	[Camshaft Position "B" - Timing Over-Advanced or System Performance (Bank 2)]	◦	◦
P0030	[B1S1A/F sensor heater characteristic]	◦	◦
P0031	[B1S1A/F sensor heater circuit Low]	◦	◦
P0032	[B1S1A/F sensor heater circuit High]	◦	◦
P0037	[B1S2O2 sensor heater circuit Low]	◦	◦
P0038	[B1S2O2 sensor heater circuit High]	◦	◦
P0068	[Manifold Pressure Sensor Range/Performance]	◦	◦
P0087	[High-pressure fuel system Low]	◦	◦
P0088	[High-pressure fuel system High]	◦	◦
P0101	[Air flow sensor characteristic]	◦	◦
P0102	[Air flow sensor circuit Low]	◦	◦
P0103	[Air flow sensor circuit High]	◦	◦
P0107	[Intake pressure sensor circuit Low]	◦	◦
P0108	[Intake pressure sensor circuit High]	◦	◦
P0111	[Intake temperature sensor characteristic]	◦	◦
P0112	[Intake temperature sensor circuit Low]	◦	◦
P0113	[Intake temperature sensor circuit High]	◦	◦
P0116	[Engine Coolant Temp. Sensor Circuit Range/Performance]	◦	◦
P0117	[Water temperature sensor circuit Low]	◦	◦
P0118	[Water temperature sensor circuit High]	◦	◦
P0122	[Throttle/Pedal Position Sensor/Switch "A" Circuit Low Input]	◦	◦
P0123	[Throttle sensor circuit High]	◦	◦
P0125	[Water temperature sensor (characteristic closed loop)]	◦	◦
P0128	[Thermostat (characteristic)]	◦	◦
P0131	[B1S1A/F sensor circuit Low]	◦	◦
P0132	[B1S1A/F sensor circuit High]	◦	◦
P0134	[B1S1A/F sensor wire Open]	◦	◦
P0137	[Oxygen Sensor Circuit Low Voltage (Bank 1 Sensor 2)]	◦	◦
P0138	[Oxygen Sensor Circuit High Voltage (Bank 1 Sensor 2)]	◦	◦
P013A	[O2 Sensor Slow Response - Rich to Lean (Bank 1 Sensor 2)]	◦	◦
P013B	[O2 Sensor Slow Response - Lean to Rich (Bank 1 Sensor 2)]	◦	◦
P013E	[O2 Sensor Delayed Response - Rich to Lean (Bank 1 Sensor 2)]	◦	◦
P013F	[O2 Sensor Delayed Response - Lean to Rich (Bank 1 Sensor 2)]	◦	◦
P0140	[Bank 1 sensor 2 O2 sensor (characteristic)]	◦	◦
P0141	[Oxygen Sensor Heater Circuit (Bank 1 Sensor 2)]	◦	◦
P014C	[O2 Sensor Slow Response - Rich to Lean (Bank 1 Sensor 1)]	◦	◦
P014D	[O2 Sensor Slow Response - Lean to Rich (Bank 1 Sensor 1)]	◦	◦
P015A	[O2 Sensor Delayed Response - Rich to Lean (Bank 1 Sensor 1)]	◦	◦
P015B	[O2 Sensor Delayed Response - Lean to Rich (Bank 1 Sensor 1)]	◦	◦
P0171	[System too Lean (Bank 1)]	◦	◦
P0172	[System too Rich (Bank 1)]	◦	◦
P0191	[Fuel Rail Pressure Sensor "A" Circuit Range/Performance]	◦	◦
P0192	[Fuel Rail Pressure Sensor Circuit Low Input]	◦	◦
P0193	[Fuel Rail Pressure Sensor Circuit High Input]	◦	◦
P0196	[Oil temperature sensor (characteristic)]	◦	◦
P0197	[Engine Oil Temperature Sensor Low]	◦	◦
P0198	[Engine Oil Temperature Sensor High]	◦	◦
P0201	[Injector Circuit / Open - (Cylinder 1)]	◦	◦
P0202	[Injector Circuit / Open - (Cylinder 2)]	◦	◦
P0203	[Injector Circuit / Open - (Cylinder 3)]	◦	◦
P0204	[Injector Circuit / Open - (Cylinder 4)]	◦	◦
P0222	[Sub-throttle sensor circuit Low]	◦	◦
P0223	[Sub-throttle sensor circuit High]	◦	◦
P0230	[Fuel pump controller circuit malfunction]	◦	◦
P0300	[Random/Multiple Cylinder Misfire Detected]	On/blink	◦
P0301	[Cylinder 1 Misfire Detected]	On/blink	◦
P0302	[Cylinder 2 Misfire Detected]	On/blink	◦
P0303	[Cylinder 3 Misfire Detected]	On/blink	◦
P0304	[Cylinder 4 Misfire Detected]	On/blink	◦
P0327	[Knock sensor 1 circuit Low]	◦	◦
P0328	[Knock sensor 1 circuit High]	◦	◦
P0332	[Knock Sensor 2 Circuit Malfunction (Low Input)]	◦	◦
P0333	[Knock Sensor 2 Circuit Malfunction (High Input)]	◦	◦
P0335	[Crank angle sensor circuit malfunction]	◦	◦
P0336	[Crank angle sensor characteristic]	◦	◦
P0340	[Camshaft Position Sensor "A" Circuit (Bank 1 or Single Sensor)]	◦	◦
P0341	[Camshaft Position Sensor "A" Circuit Range/Performance (Bank 1)]	◦	◦
P0345	[Camshaft Position Sensor "A" Circuit (Bank 2)]	◦	◦
P0346	[Camshaft Position Sensor "A" Circuit Range/Performance (Bank 2)]	◦	◦
P0351	[Ignition Coil A Primary/Secondary Circuit]	◦	◦
P0352	[Ignition Coil B Primary/Secondary Circuit]	◦	◦
P0353	[Ignition Coil C Primary/Secondary Circuit]	◦	◦
P0354	[Ignition Coil D Primary/Secondary Circuit]	◦	◦
P0365	[Camshaft Position Sensor "B" Circuit (Bank 1)]	◦	◦
P0366	[Camshaft Position Sensor "B" Circuit Range/Performance (Bank 1)]	◦	◦
P0390	[Camshaft Position Sensor "B" Circuit (Bank 2)]	◦	◦
P0391	[Camshaft Position Sensor "B" Circuit Range/Performance (Bank 2)]	◦	◦
P0420	[Catalyst deterioration]	◦	◦
P0441	[Purge Flow Monitor]	◦	◦
P0451	[ELCM evaporation system pressure sensor characteristic]	◦	◦
P0452	[Evaporative Emission Control System Pressure Sensor/Switch Low Input]	◦	◦
P0453	[Evaporative Emission Control System Pressure Sensor/Switch High Input]	◦	◦
P0455	[Evaporative Emission Control System Leak Detected (gross leak)]	◦	◦
P0456	[Evaporative Emission Control System Leak Detected (very small leak)]	◦	◦
P0458	[CPC solenoid circuit Low]	◦	◦
P0459	[CPC solenoid circuit High]	◦	◦
P0461	[Fuel level sensor (characteristic)]	◦	◦
P0462	[Fuel level sensor circuit Low]	◦	◦
P0463	[Fuel level sensor circuit High]	◦	◦
P0500	[Vehicle Speed Sensor "A"]	◦	◦
P0506	[ISC valve characteristic {1} Low]	◦	◦
P0507	[ISC valve characteristic {1} High]	◦	◦
P050A	[Cold Start Idle Air Control System Performance]	◦	◦
P050B	[Cold start ignition timing abnormal]	◦	◦
P0512	[Starter Switch Circuit High input]	◦	◦
P0560	[Back-up Voltage Circuit Malfunction]	◦	◦
P0604	[Internal Control Module Random Access Memory (RAM) Error]	◦	◦
P0605	[Internal Control Module Read Only Memory (ROM) Error]	◦	◦
P0606	[Micro-computer (CPU Failure)]	◦	◦
P060A	[Internal Control Module Monitoring Processor Performance]	◦	◦
P060B	[Internal Control Module A/D Processing Performance]	◦	◦
P0616	[Starter Relay Circuit Low]	◦	◦
P0617	[Starter Relay Circuit High]	◦	◦
P062D	[No. 1 Fuel Injector Driver Circuit Performance]	◦	◦
P062F	[EEPROM Error]	◦	◦
P0700	[AT-MIL lighting request]	◦	◦
P081A	[Starter cut relay system circuit (Low)]	◦	◦
P0851	[Neutral switch circuit Low]	◦	◦
P0852	[Neutral switch circuit High]	◦	◦
P1109	[Detected Throttle Deposit]	x	◦
P1160	[Return Spring Failure]	◦	◦
P1170	[Fuel System Abnormal (Port)]	x	◦
P117B	[Fuel System Abnormal (Di)]	x	◦
P119E	[Air-Fuel Ratio Imbalance (Bank 1) Port Injection (Fluctuation in speed)]	◦	◦
P119F	[Air-Fuel Ratio Imbalance for Direct Injection (Bank1 fluctuation engine speed)]	◦	◦
P1235	[High-pressure fuel pump abnormal]	◦	◦
P1261	[DI Injector Circuit / Open - (Cylinder 1)]	◦	◦
P1262	[DI Injector Circuit / Open - (Cylinder 2)]	◦	◦
P1263	[DI Injector Circuit / Open - (Cylinder 3)]	◦	◦
P1264	[DI Injector Circuit / Open - (Cylinder 4)]	◦	◦
P1449	[Vent control filter clogging]	◦	◦
P1451	[Fuel Tank Pressure Sensor Range/Performance]	◦	◦
P1603	[Engine Stall History]	x	◦
P1604	[Startability Malfunction]	x	◦
P2096	[Sub FB correction amount 1 lean]	◦	◦
P2097	[Sub FB correction amount 1 rich]	◦	◦
P2101	[ETC motor drive circuit]	◦	◦
P2102	[ETC motor relay power supply normally OFF]	◦	◦
P2103	[ETC motor relay power supply normally ON]	◦	◦
P2109	[Throttle angle sensor Closed position error]	◦	◦
P2119	[Throttle Control Circuit Range/Performance Problem]	◦	◦
P2122	[Main accelerator position sensor Low]	◦	◦
P2123	[Main accelerator position sensor High]	◦	◦
P2127	[Sub-accelerator position sensor Low]	◦	◦
P2128	[Sub-accelerator position sensor High]	◦	◦
P2135	[Throttle sensor characteristic]	◦	◦
P2138	[Accelerator position sensor characteristic]	◦	◦
P2195	[O2 Sensor Signal Biased/Stuck Lean (Bank 1 Sensor 1)]	◦	◦
P2196	[O2 Sensor Signal Biased/Stuck Rich (Bank 1 Sensor 1)]	◦	◦
P219A	[Air-Fuel Ratio Imbalance (Bank 1)]	◦	◦
P2401	[Evaporative Emission Leak Detection Pump Stuck OFF]	◦	◦
P2402	[Evaporative Emission Leak Detection Pump Stuck ON]	◦	◦
P2404	[Evaporative Emission System Leak Detection Pump Sense Circuit Range/Performance]	◦	◦
P2419	[Evaporate Emission System Switching Valve Control Circuit Low]	◦	◦
P2420	[Evaporate Emission System Switching Valve Control Circuit High]	◦	◦
P2610	[Soak timer IC error]	◦	◦
U0073	[Control Module Communication Bus "A" Off]	◦	◦
U0101	[Lost Communication With TCM]	◦	◦
U0122	[Lost Communication With Vehicle Dynamics Control Module]	◦	◦
U0155	[Nonarrival of H-CAN data(METER)]	◦	◦
U0402	[Invalid Data Received From TCM]	◦	◦
U0416	[Invalid Data Received From Vehicle Dynamics Control Module]	◦	◦
U0423	[Invalid Data Received From Instrument Panel Cluster Control Module]	◦	◦