LEMON Manuals: Even more car manuals for everyone
Home >> Subaru >> 2016 >> BRZ Premium >> Repair and Diagnosis >> External Pages >> Different car >> Section 4 (Power Steering System (Diagnostics)) >> Power Steering System >> Freeze Frame Data

Freeze Frame Data

WARNING: This page is about a different car, the 2014 Subaru BRZ. However, it is still accessible from the selected car via links, so may be relevant.
  1. Freeze frame data
    NOTE:
    • If an error diagnosis code is output, the freeze frame data at the time of the generation of the error code is recorded.
    • When an error diagnosis code is generated and the freeze frame data is recorded, data is not updated or deleted until the recorded data itself is deleted (diagnosis code deletion).
    1. Turn the ignition switch to OFF.
    2. Connect the SSM3 to the DLC3.
    3. Display the error code on the diagnostic code confirmation screen. (Refer to CHECK LIST FOR INTERVIEW  )
    4. Check the freeze frame data.
      LIST OF FREEZE FRAME DATA

      Item name Description/display range Normal value Remarks
      Vehicle speed Indicates the vehicle speed input from the skid control computer.
      Display range: 0.0 - 300.0 km/h      		 0 km/h: When stopped -
      No large variation: Vehicle is travelling at a constant speed -
      Engine speed Indicates the engine speed.
      Display range: 0 - 12800 rpm      		 No large variation: Engine speed is constant -
      Motor current Indicates the current flowing to the motor.
      Display range: -327.68 - 327.67 A      		 Changes in proportion to the steering force: During engine start, steering operation Left turn (+) Right turn (-)
      Motor current (requirement) Indicates the requirement for the current flowing to the motor.
      Display range: -327.68 - 327.67 A      		 Changes in proportion to the steering force: During engine start, steering operation Left turn (+) Right turn (-)
      Steering angular speed Indicates the angular speed of steering operation.
      Display range: -32768 - 32767 deg/s      		 Changes in proportion to the steering speed: During engine start, steering operation Left turn (+) Right turn (-)
      Thermistor temperature Indicates the ECM board temperature.
      Display range: -50.0 - 150.0°C      		 - -
      PIG power supply voltage Indicates the power supply voltage to drive the motor.
      Display range: 0.0000 - 20.1531 V      		 9 - 16 V: Always -
      IG power supply voltage Indicates the ECM power supply state.
      Display range: 0.0000 - 20.1531 V      		 9 - 16 V: IG ON -
      Steering torque Indicates the steering torque.
      Display range: -7.00 - 7.00 Nm      		 Changes in proportion to the steering force: During engine start, steering operation Left turn (+) Right turn (-)
      Motor rotation angle Indicates the motor rotation angle.
      Display range: 0.000 - 360.000 deg      		 Varies between 0 and 360 deg: During engine start and steering operation -
      Motor current (Command Value 2) Indicates the requirement for the current flowing to the motor.
      Display range: -327.68 - 327.67 A      		 Changes in proportion to the steering force: During engine start, steering operation -
      Boost voltage after the coil. Indicates the boost voltage after the coil.
      Display range: 0.000 - 98.000 V      		 Approx. 27 V: During engine start, steering non-operation -
      Varies within 16 - 35 V: During engine start and steering operation -
      Motor power supply voltage Indicates the motor power supply voltage.
      Display range: 0.000 - 98.000 V      		 Approx. 27 V: During engine start, steering non-operation -
      Varies within 4 - 35 V: During engine start and steering operation -
      Motor terminal voltage (U phase) Indicates the motor U terminal voltage.
      Display range: 0.000 - 98.000 V      		 Varies within 4 - 35 V: During engine start and steering operation -
      Motor terminal voltage (V phase) Indicates the motor V terminal voltage.
      Display range: 0.000 - 98.000 V      		 Varies within 4 - 35 V: During engine start and steering operation -
      Motor terminal voltage (W phase) Indicates the motor W terminal voltage.
      Display range: 0.000 - 98.000 V      		 Varies within 4 - 35 V: During engine start and steering operation -
      Torque sensor 1 output Indicates the torque sensor 1 output.
      Display range: 0.0000 - 5.0000V      		 2.3 - 2.7 V: During engine start, no steering load (neutral position) -
      2.3 - 3.8 V: During engine start, steering to the right -
      1.2 - 2.7 V: During engine start, steering to the left -
      Torque sensor 2 output Indicates the torque sensor 2 output.
      Display range: 0.0000 - 5.0000V      		 2.3 - 2.7 V: During engine start, no steering load (neutral position) -
      1.2 - 2.7 V: During engine start, steering to the right -
      2.3 - 3.8 V: During engine start, steering to the left -
      Torque sensor 1 (zero point value) Indicates the torque sensor 1 output value at the zero point.
      Display range: 0.0000 - 5.0000V      		 - -
      Torque sensor 2 (zero point value) Indicates the torque sensor 2 output value at the zero point.
      Display range: 0.0000 - 5.0000V      		 - -
scientia non olet · About LEMON Manuals