Function Inspection

1. Inspection of LED light
   1. Check that the indicators and the warning lights turn on for the following periods of time when turning IG from OFF to ON.

      Criteria

      CRITERIA SPECIFICATION
      
      

      Indicator/warning light	Lighting specifications
      A/T OIL TEMP(2), fuel	Turns on for approximately 2 seconds upon IG OFF →ON
      Auto leveling (1), driver's seat belt, brake, TRC OFF, VSC OFF, VSC SPORT	Turns on for approximately 3 seconds upon IG OFF →ON
      Airbag	Turns on for approximately 6 seconds upon IG OFF →ON
      VSC, ABS, charge, oil pressure, check engine, P/S	Turns on upon IG OFF →ON
      (1) Headlight discharge type (2) Automatic transmission system

      NOTE:

      • The lighting request is issued by the corresponding ECM.
      • Check the brake warning light after releasing the parking brake.
2. Inspection of seat belt warning indicator
   1. With IG ON, insert the tongue plate of the driver's seat belt into the buckle, and check that the seat belt warning indicator turns from ON to OFF.

      Criteria

      CRITERIA SPECIFICATION
      
      

      Indicator/warning light	Ignition switch operation	Lighting specifications
      Seat belt warning	IG OFF →ON	Blinking →Insert tongue plate →Turns off Off →Remove tongue plate →Blinking

1. Operation inspection
   1. Using a speed meter tester, check the speed meter reading error and the odometer operation.

      Standard value

      Km/h display

      METER READING DISPLAY SPECIFICATION
      
      

      Standard speed reading by tester [km/h]	Allowable range of meter reading [km/h]
      20	19.3 to 22.7
      40	39.1 to 42.9
      60	58.8 to 63.2
      80	78.8 to 83.2
      100	98.8 to 103.2
      120	118.8 to 123.2
      140	138.8 to 143.2
      160	158.8 to 163.2
      180	178.8 to 183.2
      200	198.8 to 203.2
      220	218.8 to 223.2
      240	238.8 to 243.2

      MPH display

      MPH DISPLAY SPECIFICATION
      
      

      Standard speed reading by tester [km/h]	Allowable range of meter reading [MPH]
      20	19.4 to 21.8
      40	39.3 to 41.9
      60	59.3 to 61.9
      80	79.3 to 81.9
      100	99.3 to 101.9
      120	119.3 to 121.9
      140	139.3 to 141.9

      CAUTION: Adjust the tire pressure in advance. Inappropriate tire pressure increases reading error.
   2. Check the fluctuation range of the pointer.

      Standard value: 0.3° or less

1. Operation inspection
   1. Start the engine.
   2. Use a revolution indicator to check the reading error of the tachometer.

      Standard value

      METER READING SPECIFICATION
      
      

      Revolution indicator reading [r/min]	Allowable range of meter reading [r/min]
      1000	933 to 1067
      2000	1923 to 2077
      3000	2913 to 3088
      4000	3913 to 4088
      5000	4913 to 5088
      6000	5913 to 6088
      7000	6913 to 7088
      8000	7913 to 8088

      CAUTION: Do not increase the engine speed beyond the allowable limit. (Keep the engine speed below the red zone displayed on the meter.)
   3. Check the fluctuation range of the pointer.

      Standard value: 0.3° or less

SST 09843-18040

1. Operation inspection
   1. Disconnect the connector of the engine oil pressure switch assembly.
   2. Start the engine.
   3. Using SST (diagnosis check wire No. 2), check the state of the oil pressure warning indicator when the vehicle wiring harness connector terminal is short-circuited to the chassis ground.

      Criteria: Engine oil pressure warning indicator turns on.