LEMON Manuals: Even more car manuals for everyone
Home >> Subaru >> 2014 >> Outback 2.5i, Standard Trans >> Repair and Diagnosis >> External Pages >> Different car >> Section 10 (Body Control System (Diagnostics)) >> Registration Body Integrated Unit >> Operation >> Destination Setting

Destination Setting

WARNING: This page is about a different car, the 2014 Subaru Forester. However, it is still accessible from the selected car via links, so may be relevant.
NOTE: For the vehicle requiring the destination setting, if the destination setting is not finished, display can not be shifted into customizing screen.
Step Check Yes No
1 CONFIRM CURRENT SETTING. 
Always perform confirmation of current setting before replacing the module.
Record the contents of the "Destination Setting".
NOTE: Refer to the "Read Current Data" and "CONFIRMATION OF CURRENT SETTING" to confirm the current setting. < Ref. to CONFIRM CURRENT SETTING , OPERATION, Registration Body Integrated Unit. > < Ref. to OPERATION , Read Current Data. >
 Is the current setting recorded? Go to step 2.  Confirm the current setting. Go to step 1  .
2 CONFIRM DESTINATION SETTING. 
  1. Connect the Subaru Select Monitor, and run the application.
  2. On «Main Menu» display, select {Each System Check}.
  3. On the «System Selection Menu» display, select {Integ. unit mode}.
  4. On «Integ. unit mode» display, select {Work Support}.
  5. On «Work Support» display, select {Unit customizing}.
  6. The vehicle destination screen is displayed.
 Is the vehicle destination setting screen displayed? Go to step 3.  Go to step 4  .
3 CONFIRM DESTINATION SETTING. 
Confirm the screen displayed on Subaru Select Monitor and the actual vehicle destination.		 Is it necessary to change the destination setting? Select [Yes], Go to step 4  . Select [No], Go to step 5  .
4 ENTER DESTINATION CODE. 
Enter the appropriate code in the screen. U4, U5, U6, C4: U400
C0, C5: C000		 Is the appropriate code entered? Select [OK]. Go to step 5  . Enter the destination code. Go to step 4  .
5 REGISTER VEHICLE EQUIPMENT. 
Customizing screen is displayed.
NOTE: Match the each item setting of body integrated unit registration item list with the vehicle equipment.
 Do all setting contents match with the vehicle equipment specification? Go to step 6.  Change the items until each content setting match with the vehicle equipment specification. Go to step 5  .
6 CONFIRM MARKET MODE. 
  1. Customizing screen, select the {Factory initial setting} to change the setting from "Factory" mode to "Market" mode.
  2. Turn the ignition switch to OFF.
    NOTE: When the setting is changed from "Factory" mode to "Market" mode, turning the ignition switch from ON → OFF confirms the setting.
  3. Turn the ignition switch to ON, and check the contents of settings.
 Is the mode changed to "Market" mode? Go to step 7.  Perform the destination setting from the first step. Go to step 1  .
7 CONFIRM MARKET MODE. 
Check the following.
  • Destination: When U4, U5, U6, and C4 are set

    The "Destination Setting" in the current data display is U4, U5, U6, and C4.

  • Destination: When C0 and C5 are set (models without keyless access)

    The "Destination Setting" in the current data display is C0 and C5.

 Is the display the same as indicated? Registration of body integrated unit is finished. It is possible that harness malfunction may occur. Perform the diagnosis.
NOTE: How to confirm when the destination code is not known.
Option code (destination code + OP code) Application range Destination code
U4** Must be set for all vehicles. U400
U5**
U6**
C4**
C0** Must be set only for models without keyless access. C000
C5**
scientia non olet · About LEMON Manuals