LEMON Manuals: Even more car manuals for everyone
Home >> Subaru >> 2013 >> Outback Base, Automatic CVT Trans >> Repair and Diagnosis >> External Pages >> Different car >> Section 6 (Cruise Control System (Diagnostics)) >> List of Cancel Code >> List

List of Cancel Code: List

WARNING: This page is about a different car, the 2013 Subaru Forester. However, it is still accessible from the selected car via links, so may be relevant.
NOTE:
  • The cancel code is registered even when cancel is performed intentionally by the driver.
  • Cancel codes are cleared if the ignition switch is turned to OFF.
  • If a different cancel code is input after a cancel code (latest code) has been input, the latest code is overwritten.
  • If the cruise indicator light is flashing, a malfunction is occurring in the system or cruise control related switch. The cancel code at this time is saved even after ignition switch is OFF as a memory code of a past malfunction.
  • To display a cancel code, use the Subaru Select Monitor to read the code after the cruise control is deactivated during a driving test.
Cancel code Item Contents of diagnosis Note
11 Main Switch Main switch of cruise control command switch is turned to OFF, and then the cruise control is released. This code is displayed without operating the main switch.< Refer to 11 , Diagnostic Procedure with Cancel Code. >
12 Stop Light & Brake Switch Stop light switch or brake switch is turned to ON, and then the cruise control is released. This code is displayed without depressing the brake pedal.< Refer to 12 , Diagnostic Procedure with Cancel Code. >
13 Clutch Switch Clutch switch is turned to ON, and then the cruise control is released. This code is displayed without depressing the clutch pedal.< Refer to 13 , Diagnostic Procedure with Cancel Code. >
14 Neutral Position Switch Neutral position switch is turned to ON, and then the cruise control is released. This code is displayed without shifting to neutral position.< Refer to 14 , Diagnostic Procedure with Cancel Code. >
15 Cancel Switch Cancel switch is turned to ON, and then the cruise control is released. This code is displayed without operating the cancel switch.< Refer to 15 , Diagnostic Procedure with Cancel Code. >
16 Ignition switch Ignition switch is turned to OFF, and then the cruise control is released. This code is displayed without operating the ignition switch.< Refer to 16 , Diagnostic Procedure with Cancel Code. >
21 Cruise control switch malfunction when ignition switch is turned to ON When the ignition switch is turned to ON, each switch of cruise control command switch is already turned to ON. This code is displayed when the ignition switch is turned to ON without operating the cruise control command switch.< Refer to 21 , Diagnostic Procedure with Cancel Code. >
22 Abnormality of change in vehicle speed Malfunction of vehicle speed signal variation is detected. < Refer to 22 , Diagnostic Procedure with Cancel Code. >
24 Abnormality of switches related to cruise control Open circuit of the cruise control switch is detected during cruise driving. (The system is judged as model without cruise control.) This code is displayed with normal operation.< Refer to 24 , Diagnostic Procedure with Cancel Code. >
25 Abnormality of input circuit for Brake switch Malfunction of brake switch input circuit in ECM is detected. < Refer to 25 , Diagnostic Procedure with Cancel Code. >
31 Abnormal engine speed Signal
  • Abnormal increase of engine speed is detected.
  • Gear is placed in Neutral, 1st or Reverse position.
 Cruise in 2nd shift position or more.< Refer to 31 , Diagnostic Procedure with Cancel Code. >
32 Cruse Control out of Range
  • Controlled vehicle speed decreased under the limit during cruising.
  • Set operation was performed at vehicle speed unavailable for setting.
  • RESUME operation was performed without memorized vehicle speed.
 This code is displayed, though the vehicle speed is increased to the speed available for cruise set and set operation was performed again.< Refer to 32 , Diagnostic Procedure with Cancel Code. >
34 Prohibition of cruise control at continuing big Accel. angle The vehicle has been driven at higher speed than set vehicle speed for an abnormally long time (approximately 10 minutes) during cruise driving. This code is displayed when driving for a long period of time at higher speed than appropriate cruise set vehicle speed by operating accelerator pedal. In this case, the cruise setting is deactivated.< Refer to 34 , Diagnostic Procedure with Cancel Code. >
35 Prohibition of cruise control at vehicle speed F/B malfunction Set vehicle speed cannot be kept because of some reasons (steep uphill, parking brake, abnormal decrease of engine output, etc.) during cruise driving. This code is displayed when driving condition is not suitable for cruise control. Perform cruise set operation again after clearing the possible cause.< Refer to 35 , Diagnostic Procedure with Cancel Code. >
41 VDC/TCS Operating Vehicle dynamics control (VDC) or TCS is operated during cruise driving or cruise setting. This code is displayed when driving condition is not suitable for cruise control. Perform cruise set operation again after clearing the possible cause.< Refer to 41 , Diagnostic Procedure with Cancel Code. >
43 ABS/VDC Failure ABS or Vehicle dynamics control (VDC) system malfunction is detected during cruise driving or cruise setting. < Refer to 43 , Diagnostic Procedure with Cancel Code. >
44 Body Integrated unit Failure Body integrated unit system malfunction is detected during cruise driving or cruise setting. < Refer to 44 , Diagnostic Procedure with Cancel Code. >
45 Meter Failure Combination meter malfunction is detected during cruise driving or cruise setting. < Refer to 45 , Diagnostic Procedure with Cancel Code. >
61 Brake switch abnormal Malfunction in the stop light & brake switch is detected. < Refer to 61 , Diagnostic Procedure with Cancel Code. >
62 Neutral Switch Failure Neutral position switch malfunction is detected. < Refer to 62 , Diagnostic Procedure with Cancel Code. >
63 Abnormality of change in vehicle speed Malfunction of vehicle speed signal variation is detected. < Refer to 63 , Diagnostic Procedure with Cancel Code. >
64 Engine Sensor Failure 1 Malfunction related to engine is detected. < Refer to 64 , Diagnostic Procedure with Cancel Code. >
65 Abnormality 1 of switches related to cruise control Cruise control command switch malfunction is detected. (When the switch is pressed ON for a long time (approximately two minutes), stuck ON condition is detected.) < Refer to 65 , Diagnostic Procedure with Cancel Code. >
66 Cruise Control Calculation Error Cruise control calculation (microcomputer) malfunction is detected. < Refer to 66 , Diagnostic Procedure with Cancel Code. >
scientia non olet · About LEMON Manuals