Marker Adjustment Mode

WARNING: This page is about a different car, the 2013 Subaru Forester. However, it is still accessible from the selected car via links, so may be relevant.

Navigation system

Prepare the target point. < Refer to INSPECTION , Rearview Camera System. >
With the main power OFF, press and hold the button (c) for 3 seconds or more while pressing the buttons (a) and (b) simultaneously.

Fig 1: Identifying Navigation Connection Buttons
Courtesy of SUBARU OF AMERICA, INC.

NOTE:
Pressing the button (a) for 3 seconds or more, or turning the ignition switch from ACC OFF to ON position can exit the diagnostic mode.
Line Diag screen is displayed.

Fig 2: Identifying Line Diag Screen
Courtesy of SUBARU OF AMERICA, INC.
Touch {Camera Setting} key to display «Camera Setting» screen.
Touch {S} key.

Fig 3: Identifying Line Diag Camera Setting Screen
Courtesy of SUBARU OF AMERICA, INC.
Shift the select lever to the "R" position to display the image of the rearview camera.
Touch the adjustment keys (d), (e), (f) and (g) on the display screen to adjust the marker line.

Fig 4: Identifying Rearview Camera Setting Screen
Courtesy of SUBARU OF AMERICA, INC.
1. Confirm that the target point position in the display screen is identified.
2. Adjust by touching the adjustment keys so that the cross line and target point join together.
Turn the ignition switch to OFF and wait for 60 seconds or more before turning the ignition switch to ON again.
CAUTION:
If the ignition switch is turned to OFF, be sure to wait for 60 seconds or more before turning the ignition switch to ON again.

If turning the ignition switch to ON again or disconnecting the ground cable from battery within 60 seconds after turning the ignition switch to OFF, the navigation unit data updating can not be performed correctly.
Shift the select lever to the "R" position to display the image of the rearview camera.
Confirm that the marker line position is correctly adjusted before turning the ignition switch to OFF, then finish the procedures.
- Display audio
CAUTION:
When replacing the audio unit, be sure to replace with specified audio unit. The marker adjustment can not be performed correctly if replacing with unspecified audio unit.

With the main power OFF, turn the TUNE/TRACK/CH dial (b) by 30 clicks while pressing the preset 6 key (a).

Fig 5: Identifying Tune/Track/CH Dial And Preset Key
Courtesy of SUBARU OF AMERICA, INC.
When the version information screen is displayed, press the MENU/ENTER key (c).

Fig 6: Identifying Menu/Enter Key
Courtesy of SUBARU OF AMERICA, INC.
When the uploader screen is displayed, press the MENU/ENTER key (c).

Fig 7: Identifying Menu/Enter Key
Courtesy of SUBARU OF AMERICA, INC.
When the rearview camera marker adjust screen is displayed, press and hold the MENU/ENTER key (c).

Fig 8: Identifying Menu/Enter Key
Courtesy of SUBARU OF AMERICA, INC.

NOTE:
When the ENTER key (c) is tapped, the version information screen is displayed again.

With the image of the rearview camera displayed, adjust the rearview camera marker.

CAUTION:

Operate the keys shown in the table only.

Fig 9: Display - Rearview Camera Marker Adjustment Screen

Courtesy of SUBARU OF AMERICA, INC.

Key operation	Contents
TUNE/TRACK/CH dial CCW	Line marker moves upward.
TUNE/TRACK/CH dial CW	Line marker moves downward.
«key	Line marker moves to the right.
»key	Line marker moves to the left.
MENU/ENTER key	Modified line marker position is determined, and then rearview camera marker screen is displayed.

Turn the ignition switch to OFF and wait for 60 seconds or more before finishing the procedures.
CAUTION:
Do not turn the ignition switch to ON or disconnect the ground cable from battery within 60 seconds after turning the ignition switch to OFF. The audio unit data updating can not be performed correctly.