User Customizing: Operation

On << Main Menu >> display, select {Each System Check}.
On << System Selection Menu >> display, select {Integ. unit mode}.
On << Integ. unit mode failure diag. >> display, select {Integ. Unit customizing}.

Change the setting with UP/DOWN key and set with the [OK] key.

List of User Customizing item

USER CUSTOMIZING ITEM REFERENCE CHART

Data	Initial setting value	Customize setting	Remarks
Off delay time	Long		Delay time below can be selected by setting.
		OFF	0 second
		Short	10 seconds
		Normal	20 seconds
		Long	30 seconds
Rr Defogger op. mode	15 minutes	15 minutes	Automatically stops in 15 minutes after switch is turned to ON.
Rr Defogger op. mode	15 minutes	Continuous	Repeats active condition for 15 minutes and inactive condition for 2 minutes until switch is turned to OFF.
Security Alarm Setup	ON	ON	Security alarm (hazard, horn or siren) in active condition
Security Alarm Setup	ON	OFF	Security alarm in inactive condition
Impact Sensor Setup	OFF	ON	Workable when Impact Sensor Setup is set to "ON". Impact sensor function becomes activated.
Impact Sensor Setup	OFF	OFF	Impact sensor in inactive condition (Set to "OFF" in models without sensors.)
Alarm delay setup	ON		After the keyless lock operation, the alarm monitor starts after the following delay time has passed.
		ON	Delay time is 30 seconds.
		OFF	Delay time is 0 seconds.
Lockout prevention	ON	ON	Lockout prevention in active condition. (The function does not operate if safety knob is locked by hand.)
Lockout prevention	ON	OFF	Lockout prevention in inactive condition
Impact sensor (OP)	OFF	ON	Vehicle is controlled in impact sensor equipped mode. (Make sure to set to "OFF" for models without the impact sensor. When "ON", hazard, horn or siren become activated by keyless lock (alarm monitor start).
Impact sensor (OP)	OFF	OFF	Vehicle is controlled in no impact sensor mode.
Buzzer beeping setup	ON	ON	When lock/unlock is selected by keyless entry system operation, buzzer operates.
Buzzer beeping setup	ON	OFF	When lock/unlock is selected by keyless entry system operation, buzzer does not operate.
Emergency light setup	ON	ON	When lock/unlock is selected by keyless entry system operation, buzzer operates.
Emergency light setup	ON	OFF	When lock/unlock is selected by keyless entry system operation, buzzer does not operate.
Buzzer setting	ON	ON	Vehicle is controlled in answer-back buzzer equipped mode.
Buzzer setting	ON	OFF	Vehicle is controlled in answer-back buzzer non-equipped mode. (Make sure to set to "OFF" in models without answer back buzzers.)
Initial keyless setting	-	-	-
Initial keyless setting	-	Execution	Settings of keyless entry system are initialized.
Initial button setting	-	-	-
Initial button setting	-	Execution	Settings of each function are initialized.
Passive Alarm	OFF	ON	Setting only for North American models
Passive Alarm	OFF	OFF	Setting only for North American models
Door open warning	ON	ON	If detecting door open for 20 minutes, room light, map light, and key ring illumination that are related to doors are turned off to prevent battery runout.
Door open warning	ON	OFF	Room light, map light, key illumination and door warning light are not turned off.
Dome Light Alarm Setting	OFF	ON	The room light lights by being interlocked with the activation of the alarm.
Dome Light Alarm Setting	OFF	OFF
Map Light Setting	ON	ON	Illuminates in accordance with the door interlocked room light.
Map Light Setting	ON	OFF
Belt Warning Switch	ON	ON	When using normally
Belt Warning Switch	ON	OFF	Stop the belt warning buzzer beep and warning light illumination.

After setting, make sure that the setting changed {Current Data Display & Save} is same as vehicle equipment.
CAUTION:
- The above settings must match the actual vehicle equipment.
- Do not change settings except for setting above while setting the functions.
- Be sure not to change Factory initial setting except when installing a new body integrated unit.
NOTE: For detailed operation procedures, refer to PC application help for Subaru Select Monitor.