LEMON Manuals: Even more car manuals for everyone
Home >> Subaru >> 2010 >> Impreza Outback Sport, Automatic >> Repair and Diagnosis >> Transmission >> Automatic Trans >> Automatic Transmission >> Front Vehicle Speed Sensor >> Installation

Front Vehicle Speed Sensor: Installation

  1. Pass the transmission harness assembly through the hole of the transmission case.
    Fig 1: Identifying Transmission Harness Assembly
    G05002532Courtesy of SUBARU OF AMERICA, INC.
  2. Connect the control valve connector and transmission ground.

    Tightening torque: 

    8 N.m (0.8 kgf-m, 5.9 ft-lb) 

    Fig 2: Identifying Control Valve Connector And Transmission Ground
    G06349270Courtesy of SUBARU OF AMERICA, INC.
  3. Apply proper amount of liquid gasket to the entire oil pan mating surface.

    Liquid gasket: 

    THREE BOND 1217B (Part No. K0877YA020) or equivalent 

    Fig 3: Applying Proper Amount Of Liquid Gasket To Entire Oil Pan Mating Surface
    G05002534Courtesy of SUBARU OF AMERICA, INC.
  4. Fill the 3 locations of the transmission case excluding the bolt holes with an ample amount of liquid gasket.

    Liquid gasket: 

    THREE BOND 1217B (Part No. K0877YA020) or equivalent 

    Fig 4: Locating Liquid Gasket Applying Locations On Bolt Holes
    G05956004Courtesy of SUBARU OF AMERICA, INC.
  5. Install the oil pan by equally tightening the bolts.

    Tightening torque: 

    5 N.m (0.5 kgf-m, 3.7 ft-lb) 

  6. Install the front vehicle speed sensor and torque converter turbine speed sensor.

    Tightening torque: 

    7 N.m (0.7 kgf-m, 5.2 ft-lb) 

  7. Connect the connector to the rear vehicle speed sensor.
  8. Install the ATF inlet and outlet pipes.
    NOTE: Use a new copper washer.

    Tightening torque: 

    T1: 25 N.m (2.5 kgf-m, 18.4 ft-lb) 

    T2: 40 N.m (4.1 kgf-m, 29.5 ft-lb) 

    T3:45 N.m (4.6 kgf-m, 33.2 ft-lb) 

    Fig 5: Identifying ATF Inlet And Outlet Pipes
    G05956005Courtesy of SUBARU OF AMERICA, INC.
  9. Install the transmission rear crossmember bolt.

    Tightening torque: 

    70 N.m (7.1 kgf-m, 51.6 ft-lb) 

  10. Install the propeller shaft. Ref. to INSTALLATION in Propeller Shaft.
  11. Install the heat shield cover.
    Fig 6: Identifying Heat Shield Cover
    G05661183Courtesy of SUBARU OF AMERICA, INC.
  12. Install the front, center and rear exhaust pipes, and the muffler. (Non-turbo model)

    Ref. to INSTALLATION in Front Exhaust Pipe. Ref. to INSTALLATION in Center Exhaust Pipe. Ref. to INSTALLATION in Rear Exhaust Pipe. Ref. to INSTALLATION in Muffler.

  13. Install the center, rear exhaust pipes and the muffler. (Turbo model) Ref. to INSTALLATION in Center Exhaust Pipe. Ref. to INSTALLATION in Rear Exhaust Pipe. Ref. to INSTALLATION in Muffler.
  14. Lower the vehicle.
  15. Install the transmission harness connector to the stay.
  16. Install the pitching stopper. Ref. to INSTALLATION  in Transmission Mounting System.
  17. Install the air intake chamber. (Non-turbo model) Ref. to INSTALLATION in Air Intake Chamber.
  18. Install the intercooler. (Turbo model)

    Ref. to INSTALLATION in Intercooler.

  19. Fill with the same amount of ATF as drained. Ref. to AUTOMATIC TRANSMISSION FLUID .
  20. Bleed the air of control valve.

    Ref. to PROCEDURE  in Air Bleeding of Control Valve.

  21. Inspect the level of ATF. Ref. to INSPECTION  in Automatic Transmission Fluid.
  22. Perform learning control promotion. Ref. to FACILITATION OF LEARNING CONTROL in OPERATION, Subaru Select Monitor.
scientia non olet · About LEMON Manuals