LEMON Manuals: Even more car manuals for everyone
Home >> Subaru >> 2009 >> Outback Limited >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Communication Devices >> LAN Communication System - LAN (Diagnostics) >> Subaru Select Monitor >> Operation >> Function Setting (ECM Customizing)

Function Setting (ECM Customizing)

  1. On the «Main Menu» display, select the {Each System Check}.
  2. On the «System Selection Menu» display, select the {Integ. unit mode}.
  3. On the «Integ. unit mode failure diag» display, select the {ECM customizing}.
  4. Change the setting with UP/DOWN key and set with the [OK]. List of function setting item (ECM customizing)
    FUNCTION SETTING ITEM (ECM CUSTOMIZING) REFERENCE

    Data Initial setting value Customize setting Remarks Destination Specifications
    Off delay time Normal   Delay time below can be selected by setting.  
    After door closed After keyless unlock
    OFF 0 sec. 0 sec.
    Short 3 sec. 10 sec.
    Normal 5 sec. 20 sec.
    Long 8 sec. 30 sec.
    Outside Temp. Offset 0°C -2 - +2 (increment of 0.5) If it is set to +2.0°C at outside temperature of 12°, the displayed outside temperature will be 14°C.  
    Rr defogger op. mode 15 min. 15 min. Automatically stops in 15 minutes after switch is turned to ON.  
    Continuous Repeats active condition for 15 minutes and inactive condition for 2 minutes until switch is turned to OFF.  
    Wiper deicer op. mode 15 min. 15 min. Automatically stops in 15 minutes after switch is turned to ON.  
    Continuous Repeats active condition for 15 minutes and inactive condition for 2 minutes until switch is turned to OFF.  
    Security Alarm Setup ON ON Security alarm (hazard, horn or siren) in active condition  
    OFF Security alarm in inactive condition  
    Impact Sensor Setup OFF ON Workable when Impact Sensor Setup is set to "ON". Impact sensor in active condition  
    OFF Impact sensor in inactive condition (Always set to OFF for vehicles not equipped with the sensor.)  
    Alarm delay setup ON   After doors are locked by keyless entry system operated, the alarm monitor starts in following time.  
    ON Delay time is 30 seconds.
    OFF Delay time is 0 seconds.
    Lockout prevention ON ON Lockout prevention in active condition (The function does not operate if safety knob is locked by hand.)  
    OFF Lockout prevention in inactive condition  
    Impact sensor OFF ON Vehicle is controlled in impact sensor equipped mode. (Make sure to set to OFF for models without the impact sensor. When set to "ON", hazard, the horn or siren will operate after doors are locked by the keyless entry system operation (Alarm monitor start). Set to "ON" when an optional impact sensor is installed.
    OFF Vehicle is controlled in impact sensor no-equipped mode.
    Answer-back buzzer setup ON ON Workable when answer-back buzzer setup is set to "ON". When lock/unlock is selected by keyless entry system operated, answer-back buzzer operates.  
    OFF When lock/unlock is selected by keyless entry system operated, answer-back buzzer does not sound.
    Hazard answer-back setup ON ON Workable when hazard answer-back setup is set to "ON". When lock/unlock is selected by keyless entry system operated, hazard answer-back buzzer operates.  
    OFF When lock/unlock is selected by keyless entry system operated, hazard answer-back does not operate.
    Ans.-back Buzzer ON ON Vehicle is controlled in answer-back buzzer equipped mode.  
    OFF Vehicle is controlled in answer-back buzzer non-equipped mode. (Always set to OFF for vehicles not equipped with the answer-back.)
    Initial keyless setting - - -  
    Execution Settings of keyless entry system are initialized. (Auto-lock time: 30 sec, Answer-back buzzer setup: ON, Hazard answer-back setup: ON, Automatic locking setup: ON, Ans.-back Buzzer: ON)
    Initial button setting - - -  
    Execution Settings of each function are initialized. (Off delay time: Normal, R defogger op. mode: 15 min. Wiper deicer op. mode: 15 mm. Lockout prevention: ON)
    Passive Alarm OFF ON Workable when passive arming is set to "ON."  
    OFF
    Door open warning (prevention of battery run-out) ON ON If detecting door open for 10 minutes, room light, key illumination and door warning light are turned off to prevent battery run-out.  
    OFF Room light, key illumination and door warning light is not turned off.
    Belt Warning Switch OFF ON Alarm is set off with the indicator lit and buzzer beep from the first to third stage according to the vehicle speed and whether or not seat belts are worn.  
    OFF Turns off the indicator and stops buzzer except for the first stage.
  5. After setting, make sure that vehicle equipment is same as the setting changed in the {Current Data Display & Save}.
    CAUTION:
    • The above settings must match the actual vehicle equipment for proper operation.
    • Do not change settings except for setting above while setting the functions.
    • Be sure not to change Factory or Market setting except when installing a new body integrated unit.
    NOTE: For details concerning the operation procedure, refer to Subaru Select Monitor .