Adjusting Parts
WARNING: This page is about a different car, the 2008 Subaru Impreza. However, it is still accessible from the selected car via links, so may be relevant.
PRELOAD ADJUSTING SPACER LENGTH SPECIFICATION
| Part No. | Length mm (in) | |
|---|---|---|
| Preload adjusting spacer | 383695201 | 56.2 (2.213) |
| 383695202 | 56.4 (2.220) | |
| 383695203 | 56.6 (2.228) | |
| 383695204 | 56.8 (2.236) | |
| 383695205 | 57.0 (2.244) | |
| 383695206 | 57.2 (2.252) |
PRELOAD ADJUSTING WASHER THICKNESS
| Part No. | Thickness mm (in) | |
|---|---|---|
| Preload adjusting washer | 383705200 | 2.59 (0.1020) |
| 383715200 | 2.57 (0.1012) | |
| 383725200 | 2.55 (0.1004) | |
| 383735200 | 2.53 (0.0996) | |
| 383745200 | 2.51 (0.0988) | |
| 383755200 | 2.49 (0.0980) | |
| 383765200 | 2.47 (0.0972) | |
| 383775200 | 2.45 (0.0965) | |
| 383785200 | 2.43 (0.0957) | |
| 383795200 | 2.41 (0.0949) | |
| 383805200 | 2.39 (0.0941) | |
| 383815200 | 2.37 (0.0933) | |
| 383825200 | 2.35 (0.0925) | |
| 383835200 | 2.33 (0.0917) | |
| 383845200 | 2.31 (0.0909) | |
| Pinion height adjusting washer | 383495200 | 3.09 (0.1217) |
| 383505200 | 3.12 (0.1228) | |
| 383515200 | 3.15 (0.1240) | |
| 383525200 | 3.18 (0.1252) | |
| 383535200 | 3.21 (0.1264) | |
| 383545200 | 3.24 (0.1276) | |
| 383555200 | 3.27 (0.1287) | |
| 383565200 | 3.30 (0.1299) | |
| 383575200 | 3.33 (0.1311) | |
| 383585200 | 3.36 (0.1323) | |
| 383595200 | 3.39 (0.1335) | |
| 383605200 | 3.42 (0.1346) | |
| 383615200 | 3.45 (0.1358) | |
| 383625200 | 3.48 (0.1370) | |
| 383635200 | 3.51 (0.1382) | |
| 383645200 | 3.54 (0.1394) | |
| 383655200 | 3.57 (0.1406) | |
| 383665200 | 3.60 (0.1417) | |
| 383675200 | 3.63 (0.1429) | |
| 383685200 | 3.66 (0.1441) | |
| Side gear thrust washer | 383445201 | 0.75 - 0.80 (0.0295 - 0.0315) |
| 383445202 | 0.80 - 0.85 (0.0315 - 0.0335) | |
| 383445203 | 0.85 - 0.90 (0.0335 - 0.0354) | |
| Side bearing retainer shim | 383475201 | 0.20 (0.0079) |
| 383475202 | 0.25 (0.0098) | |
| 383475203 | 0.30 (0.0118) | |
| 383475204 | 0.40 (0.0157) | |
| 383475205 | 0.50 (0.0197) |
SIDE BEARING RETAINER SHIM THICKNESS
| Drive pinion bearing preload | Measure with spring measurement (Measured from the companion flange bolt) | N (Kgf, lb) | 17.7 - 38.8 (1.8 - 4.0, 4.0 - 8.7) |
| Measure with torque wrench | N.m(kgf-m, ft-lb) | 0.67 - 1.47 (0.07 - 0.15, 0.49 - 1.08) | |
| Side gear backlash | mm (in) | 0.10 - 0.20 (0.004 - 0.008) | |
| Hypoid driven gear to drive pinion backlash limit | mm (in) | 0.10 - 0.20 (0.004 - 0.008) | |
| Hypoid driven gear runout limit on its back surface | mm (in) | 0.05 (0.002) | |