Registration Body Integrated Unit (Equipment Setting)

CAUTION: Body integrated unit is core of LAN system, and also can select the function of all vehicle system control. It is possible to control the original functions of vehicle when registrations of body integrated unit and function setting are corresponded to vehicle equipment.

If registrations and function setting are different from vehicle equipment, vehicle system does not operate normally and diagnosis cannot be performed correctly. Pay attention to following item.

Be sure to correspond registrations and function settings to vehicle equipment.
Do not change the settings of vehicle improperly.
Confirm key illumination does not blink or "Factory initial setting" of body integrated unit registrations is "Market". If "Factory initial setting" is set to "Factory," key Illumination blinks when ignition key is turned ON, to notify that the settings are unconfirmed.
Key illumination does not blink with ignition switch turned to ON and go off with door closed.
Be sure to register immobilizer if body integrated unit is replaced with a new part, (models with immobilizer)
Make a registration of immobilizer when the parts related to immobilizer have been replaced. Refer to the "REGISTRATION MANUAL FOR IMMOBILIZER".

Turn the ignition switch to OFF.
Connect the Subaru Select Monitor to the data link connector.

Fig 1: Identifying Data Link Connector Location
Courtesy of SUBARU OF AMERICA, INC.
Turn the ignition switch to ON and run the Subaru Select Monitor.
On the «Main Menu» display screen, select the {Each System Check}.
On the «Each System Check» display screen, select the {Integ. Unit mode} and then select the «ECM customizing».

Change the setting with UP/DOWN key and select the [OK].

List of body integrated unit registration item

NOTE: Setting is different depending on the grade of vehicle.

INITIAL SETTING CHART

Data	Initial setting	Registration	Remarks
A/C ECM setting	OFF	ON	Illumination control does not operate if A/C ECM setting is set to "OFF" in case of model with auto A/C.
A/C ECM setting	OFF	OFF	If A/C ECM setting is set to "ON" in case of model without auto A/C, illumination change to night illumination and it is difficult to be recognized.
P/W ECM setting	OFF	ON	Set to "OFF".
P/W ECM setting	OFF	OFF	Set to "OFF".
Wiper deicer setting	OFF	ON	ON signal does not output with operation of wiper deicer switch if wiper deicer is set to "OFF" in models with a wiper deicer.
Wiper deicer setting	OFF	OFF
Rear fog light setting	OFF	ON	Set to "OFF".
Rear fog light setting	OFF	OFF	Set to "OFF".
Factory initial setting (Reset of body integrated unit)	Factory	Factory (Reset)	If Factory initial setting is set to "Factory", registrations of items above is changed to "OFF". After setting, be sure to set to "Market".
Factory initial setting (Reset of body integrated unit)	Factory	Market (Settlement)

CAUTION:

It is possible to control the original functions of vehicle when registrations of body integrated unit and function setting are corresponded to vehicle equipment.
When body integrated unit is a new part or "Factory" mode, key illumination blinks to show equipment settings have not been completed.
Be sure not to change Factory initial setting except installation of new body integrated unit.

NOTE: "Factory" mode:

Body integrated unit has not been set yet. It can be recognized by key illumination blinking with ignition switch turned to ON.
All replacement body integrated units are set to Factory mode. When replacing a body integrated unit, be sure to perform the registration operation.

"Market" mode:

Each settings have been set. It can be recognized by key illumination coming on in concocting with room light and going off with ignition switch turned to ON.

Perform the Factory setting. On the «ECM customizing» display screen of Subaru Select Monitor, select the {Factory initial setting} and select the [OK].
Change the mode from Factory to Market.
Change to the immobilizer cartridge, and register the immobilizer key. (For models with immobilizer, perform the procedures according to "IMMOBILIZER TEACHING OPERATION MANUAL".)
When key registration is completed, "Do you want to register remote engine start?" is displayed. Perform registration only for equipped models.
Perform the function setting (ECM customizing).
< Ref. to FUNCTION SETTING (ECM CUSTOMIZING) , OPERATION, Subaru Select Monitor . >

NOTE: For details concerning the operation procedure, refer to the "SUBARU SELECT MONITOR OPERATION MANUAL".