LEMON Manuals: Even more car manuals for everyone
Home >> Subaru >> 2007 >> Impreza Outback Sport, Standard >> Repair and Diagnosis >> Engine Performance >> System >> Engine Controls (Diagnostics) (H4SO) >> Subaru Select Monitor >> Operation >> Read Current Data For Engine (OBD Mode)

Read Current Data For Engine (OBD Mode)

  1. On the «Main Menu» display screen, select {Each System Check}.
  2. On the «System Selection Menu» display screen, select {Engine Control System}.
  3. Select the [OK] after the information of engine type has been displayed.
  4. On the «Engine Diagnosis» display screen, select {OBD System}.
  5. On the «OBD Menu» display screen, select {Current Data Display/Save}.
  6. On the «Data Display Menu» display screen, select {Data Display}.
  7. Using the scroll key, scroll the display screen up or down until the desired data is shown.
ENGINE CURRENT DATA DISPLAY CHART

Contents Display Unit of measure Note (at idling)
Number of diagnosis code Number of Diag. Code: - 0
Condition of malfunction indicator light MI (MIL) - OFF
Monitoring test of misfire Misfire monitoring - Supp YES or NO
Monitoring test of misfire Misfire monitoring - Rdy YES or NO
Monitoring test of fuel system Fuel system monitoring - Supp YES or NO
Monitoring test of fuel system Fuel system monitoring - Rdy YES or NO
Monitoring test of comprehensive component Component monitoring - Supp YES or NO
Monitoring test of comprehensive component Component monitoring - Rdy YES or NO
Test of catalyst Catalyst Diagnosis - Supp YES or NO
Test of catalyst Catalyst Diagnosis - Rdy YES or NO
Test of heating-type catalyst Heated catalyst - Supp N/A
Test of heating-type catalyst Heated catalyst - Rdy N/A
Test of evaporative emission purge control system Evaporative purge system - Supp YES or NO
Test of evaporative emission purge control system Evaporative purge system - Rdy YES or NO
Secondary air system test Secondary air system - Supp N/A
Secondary air system test Secondary air system - Rdy N/A
Test of air conditioning system A/C system refrigerant - Supp N/A
Test of air conditioning system A/C system refrigerant - Rdy N/A
Test of oxygen sensor O2 Sensor Diagnosis - Supp YES or NO
Test of oxygen sensor O2 Sensor Diagnosis - Rdy YES or NO
Test of oxygen sensor heater O2 Heater Diagnosis - Supp YES or NO
Test of oxygen sensor heater O2 Heater Diagnosis - Rdy YES or NO
Test of EGR system EGR system - Supp YES or NO
Test of EGR system EGR system - Rdy YES or NO
A/F control #1 Fuel system for Bank 1 - Normal CLOSE
Engine load data Calculated load valve % 23.0 %
Engine coolant temperature signal Coolant Temp. °C or °F 92°C or 198°F
A/F correction value #1 A/F Correction Value #1 % -0.8 %
A/F learning #1 A/F Learning Value #1 % +0.0 %
Intake manifold absolute pressure Mani. Absolute Pressure mmHg, kPa, inHg or psig 211 mmHg, 28.1 kPa, 8.31 inHg or 4.08 psig
Engine speed signal Engine Speed rpm 700 rpm
Vehicle speed signal Vehicle Speed km/h or MPH 0 km/h or 0 MPH
Ignition timing advance for #1 cylinder Ignition timing adv.#1 ° +16.0°
Intake air temperature signal Intake Air Temp. °C or °F 36°C or 97°F
Amount of intake air Mass Air Flow g/s or lb/m 2.7 g/s or 0.36 lb/m
Throttle opening angle signal Throttle Opening Angle % 13%
Front oxygen (A/F) sensor (Bank 1 Sensor 1) Oxygen sensor #11 - Support
Oxygen sensor (Bank 1 Sensor 1) Oxygen sensor #12 - Support
Oxygen sensor (Bank 1 Sensor 2) Oxygen sensor #12 V 0.7 V
A/F correction (Bank 1 Sensor 2) A/F Correction #12 % 0.0 %
OBD system OBD system - CARB - OBD2
Front oxygen (A/F) sensor (Bank 1 Sensor 1) A/F sensor #11 - 1.001
Front oxygen (A/F) sensor (Bank 1 Sensor 1) A/F sensor #11 V 2.79 V
Front oxygen (A/F) sensor (Bank 1 Sensor 1) A/F sensor #11 - 1.001
Front oxygen (A/F) sensor (Bank 1 Sensor 1) A/F sensor #11 mA 0.00 mA
NOTE: For detailed operation procedure, refer to the "SUBARU SELECT MONITOR OPERATION MANUAL "