LEMON Manuals: Even more car manuals for everyone
Home >> Subaru >> 2006 >> Impreza Outback Sport, Standard >> Repair and Diagnosis >> Engine Performance >> System >> Engine Controls - Engine (Diagnostics) (H4SO) >> Subaru Select Monitor >> Operation >> Read Current Data For Engine (OBD Mode)

Read Current Data For Engine (OBD Mode)

  1. On the «Main Menu» display screen, select the {Each System Check} and press the [YES] key.
  2. On the «System Selection Menu» display screen, select the {Engine} and press the [YES] key.
  3. Press the [YES] key after the information of engine type has been displayed.
  4. On the «Engine Diagnosis» display screen, select the {OBD system} and press the [YES] key.
  5. On the «OBD Menu» display screen, select the {Current Data Display/Save}, and press the [YES] key.
  6. On the «Data Display Menu» display screen, select the {Data Display} and press the [YES] key.
  7. Using the scroll key, scroll the display screen up or down until the desired data is shown.
    • A list of the support data is shown in the following table.
      LIST OF SUPPORT DATA

      DESCRIPTION Display Unit of measure Note (at idling)
      Number of diagnosis code Number of Diag. Code: - 0
      Condition of malfunction indicator light Ml (MIL) - OFF
      Monitoring test of misfire Misfire monitoring - complete
      Monitoring test of fuel system Fuel system monitoring - complete
      Monitoring test of comprehensive component Component monitoring - complete
      Test of catalyst Catalyst Diagnosis - incomplete
      Test of heating-type catalyst Heated catalyst - no support
      Test of evaporative emission purge control system Evaporative purge system - incomplete
      Test of secondary air system Secondary air system - no support
      Test of air conditioning system refrigerant A/C system refrigerant - no support
      Test of oxygen sensor O1 Sensor Diagnosis - incomplete
      Test of oxygen sensor heater O2 Heater Diagnosis - complete
      Test of EGR system EGR system - incomplete
      A/F control #1 Fuel system for Bank 1 - CLOSE normal
      Load Calculated load valve % 23.0%
      Engine coolant temperature signal Coolant Temp. °C 92°C or 198°F
      A/F correction 1 A/F Correction #1 % -0.8%
      A/F learning 1 A/F Learning #1 % +0.0%
      Intake manifold absolute pressure Mani. Absolute Pressure mmHg, kPa, inHg or psig 211 mmHg, 28.1 kPa, 8.31 inHg or 4.08 psig
      Engine speed signal Engine Speed rpm 700 rpm
      Vehicle speed signal Vehicle Speed km/h or MPH 0 km/h or 0 MPH
      Ignition timing #1 Ignition timing adv. #1 ° +16.0°
      Intake air temperature signal Intake Air Temp. °C or °F 36°C or 97°F
      Amount of intake air Mass Air Flow g/s or lb/m 2.7 g/s or 0.36 lb/m
      Throttle opening angle signal Throttle Opening Angle % 13%
      Oxygen sensor (Bank 1 Sensor 2) Oxygen sensor #12 V 0.7 V
      A/F correction (Bank 1 Sensor 2) A/F Correction #12 % 0.0%
      OBD system OBD system - CARB - OBD2
      Front oxygen (A/F) sensor (Bank 1 Sensor 1) Oxygen sensor #11 - Support
      Oxygen sensor (Bank 1 Sensor 2) Oxygen sensor #12 - Support
      Front oxygen (A/F) sensor (Bank 1 Sensor 1) A/F sensor #11 - 1.001
      Front oxygen (A/F) sensor (Bank 1 Sensor 1) A/F sensor #11 V 2.79 V
      Front oxygen (A/F) sensor (Bank 1 Sensor 1) A/F sensor #11 - 1.001
      Front oxygen (A/F) sensor (Bank 1 Sensor 1) A/F sensor #11 mA 0.00 mA
      NOTE: For detailed operation procedure, refer to "SUBARU SELECT MONITOR OPERATION MANUAL".
scientia non olet · About LEMON Manuals