LEMON Manuals: Even more car manuals for everyone
Home >> Scion >> 2015 >> tC Standard Trans >> Repair and Diagnosis >> Body & Frame >> Windows >> Power Window Control System (Diagnostics - Introduction) >> Power Window Control System >> Data List / Active Test [05/2014 - ] >> Data List / Active Test [05/2014 - ]

Data List / Active Test [05/2014 - ]

  1. DATA LIST 

    HINT: 

    Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    NOTE:

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    1. Connect the Techstream to the DLC3.
    2. Turn the ignition switch to ON.
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / (desired system) / Data List.
    5. According to the display on the Techstream, read the Data List.
      D-DOOR MOTOR

      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      D Door P/W Auto SW Driver side power window auto up/down signal / ON or OFF ON: Driver side power window auto up/down switch operated
      OFF: Driver side power window switch not operated      		 -
      D Door P/W Up SW Driver side power window manual up signal / ON or OFF ON: Driver side power window manual up switch operated
      OFF: Driver side power window switch not operated      		 -
      D Door P/W Down SW Driver side power window manual down signal / ON or OFF ON: Driver side power window manual down switch operated
      OFF: Driver side power window switch not operated      		 -
      Glass Position (Close-1/4) Jam protection status of window glass within range of fully closed to 1/4 open position / OK or Caution OK: Power window regulator motor assembly LH operates normally between fully closed and 1/4 open positions
      Caution: Jam protection function operating due to detection of foreign object or irregular movement      		 -
      Glass Position (1/4-2/4) Jam protection status of window glass within range of 1/4 open to 1/2 open position / OK or Caution OK: Power window regulator motor assembly LH operates normally between 1/4 open and 1/2 open positions
      Caution: Jam protection function operating due to detection of foreign object or irregular movement      		 -
      Glass Position (2/4-3/4) Jam protection status of window glass within range of 1/2 open to 3/4 open position / OK or Caution OK: Power window regulator motor assembly LH operates normally between 1/2 open and 3/4 open positions
      Caution: Jam protection function operating due to detection of foreign object or irregular movement      		 -
      Glass Position (3/4-Open) Jam protection status of window glass within range of 3/4 open to fully open position / OK or Caution OK: Power window regulator motor assembly LH operates normally between 3/4 open and fully open positions
      Caution: Jam protection function operating due to detection of foreign object or irregular movement      		 -
      Number of Trouble Codes Number of trouble codes / Min.: 0, Max.: 255 Number of DTCs stored -
      MAIN BODY

      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      FL Door Courtesy Front door courtesy light switch assembly LH signal / ON or OFF ON: Front door LH open
      OFF: Front door LH closed      		 -
      FR Door Courtesy Front door courtesy light switch assembly RH signal / ON or OFF ON: Front door RH open
      OFF: Front door RH closed      		 -
      Communication D-Door Motor Connection status between power window regulator motor assembly LH and main body ECU / OK or STOP OK: Connected
      STOP: Not connected      		 -
  2. ACTIVE TEST 

    HINT: 

    Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

    1. Connect the Techstream to the DLC3.
    2. Turn the ignition switch to ON.
    3. Turn the Techstream on.
    4. Enter the following menus: Body Electrical / (desired system) / Active Test.
    5. According to the display on the Techstream, perform the Active Test.
      WARNING:

      Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function does not operate.

      D-DOOR MOTOR

      Tester Display Test Part Control Range Diagnostic Note
      Power Window Driver side power window OFF/UP/DOWN -

      HINT: 

      Up and down movement does not occur if the arrow is not pressed and held.

      MAIN BODY

      Tester Display Test Part Control Range Diagnostic Note
      IG OFF P/W Control Permission Output Power window OFF / ON Perform this Active Test with the ignition switch off

      HINT: 

      If Active Test is turned on, only the driver side power window does not operate.

scientia non olet · About LEMON Manuals