DTC B1771: Passenger Side Buckle Switch Circuit Malfunction[05/2013 - ]: Procedure

1. Turn the ignition switch to ON, and wait for at least 60 seconds.
2. Clear the DTCs stored in the memory. Refer to DTC CHECK / CLEAR [05/2013 - ] .

   HINT: 

   • First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor assembly.
   • Use the Techstream to clear the DTCs of the occupant classification ECU, otherwise the DTCs cannot be cleared.
3. Turn the ignition switch off.
4. Turn the ignition switch to ON, and wait for at least 60 seconds.
5. Check for DTCs. Refer to DTC CHECK / CLEAR [05/2013 - ] .

   OK

   DTC B1771 is not output.

   HINT: 

   Codes other than DTC B1771 may be output at this time, but they are not related to this check.

NG → See step   2 

OK → See step   11 

1. Turn the ignition switch off.
2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
3. Check that the connectors are properly connected to the occupant classification ECU and the front seat inner belt assembly RH.

   OK

   Connectors are properly connected.

NG → CONNECT CONNECTORS PROPERLY 

OK: Go to next step 

1. Disconnect the connectors from the occupant classification ECU and the front seat inner belt assembly RH.
2. Check that the connectors (on the occupant classification ECU side and front seat inner belt assembly RH side) are not damaged.

   OK

   Connectors are not deformed or damaged.

NG → REPLACE FRONT SEAT WIRE RH 

OK: Go to next step 

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
2. Turn the ignition switch to ON.
3. Measure the voltage according to the value(s) in the table below.

   Standard Voltage

   Tester Connection	Switch Condition	Specified Condition
   M3-9 (BSW) - Body ground	Ignition switch ON	Below 1 V
   M3-5 (BGND) - Body ground

4. Turn the ignition switch off.
5. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
6. Using a service wire, connect terminals 1 (RBE+) and 2 (RBE-) of connector C.
   NOTE:

   Do not forcibly insert the service wire into the terminals of the connector.

7. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   M3-9 (BSW) - M3-5 (BGND)	Always	Below 1 Ω

8. Disconnect the service wire from connector C.
9. Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Tester Connection	Condition	Specified Condition
   M3-9 (BSW) - Body ground	Always	1 MΩ or higher
   M3-5 (BGND) - Body ground
   M3-9 (BSW) - M3-5 (BGND)

NG → REPLACE FRONT SEAT WIRE RH 

OK: Go to next step 

1. Connect the connectors to the occupant classification ECU and the front seat inner belt assembly RH.
2. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
3. Turn the ignition switch to ON, and wait for at least 60 seconds.
4. Clear the DTCs stored in the memory. Refer to DTC CHECK / CLEAR [05/2013 - ] .

   HINT: 

   • First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor assembly.
   • Use the Techstream to clear the DTCs of the occupant classification ECU, otherwise the DTCs cannot be cleared.
5. Turn the ignition switch off.
6. Turn the ignition switch to ON, and wait for at least 60 seconds.
7. Using the Techstream, check for DTCs of the occupant classification ECU. Refer to DTC CHECK / CLEAR [05/2013 - ] .

   OK

   DTC B1771 is not output.

   HINT: 

   DTCs other than DTC B1771 may be output at this time, but they are not related to this check.

NG → See step   6 

OK → See step   11 

1. Turn the ignition switch off.
2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
3. Replace the front seat inner belt assembly RH. Refer to REMOVAL [05/2013 - ] .

   HINT: 

   Perform the inspection using parts from a normal vehicle when possible.

4. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

NEXT: Go to next step 

1. Turn the ignition switch to ON, and wait for at least 60 seconds.
2. Clear the DTCs stored in the memory. Refer to DTC CHECK / CLEAR [05/2013 - ] .

   HINT: 

   • First clear DTCs stored in the occupant classification ECU and then in the center airbag sensor assembly.
   • Use the Techstream to clear the DTCs of the occupant classification ECU, otherwise the DTCs cannot be cleared.
3. Turn the ignition switch off.
4. Turn the ignition switch to ON, and wait for at least 60 seconds.
5. Using the Techstream, check for DTCs of the occupant classification ECU. Refer to DTC CHECK / CLEAR [05/2013 - ] .

   OK

   DTC B1771 is not output.

   HINT: 

   DTCs other than DTC B1771 may be output at this time, but they are not related to this check.

NG → See step   8 

OK → END 

1. Turn the ignition switch off.
2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
3. Replace the occupant classification ECU. Refer to REMOVAL [05/2013 - ] .

   HINT: 

   Perform the inspection using parts from a normal vehicle when possible.

4. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
5. Turn the ignition switch to ON, and wait for at least 60 seconds.
6. Clear the DTCs stored in the memory. Refer to DTC CHECK / CLEAR [05/2013 - ] .

   HINT: 

   If the DTCs are not cleared at this time, past DTCs will remain.

NEXT: Go to next step 

1. Connect the Techstream to the DLC3.
2. Turn the ignition switch to ON.
3. Using the Techstream, perform the zero point calibration. Refer to INITIALIZATION [05/2013 - ] .

NEXT: Go to next step 

1. Using the Techstream, perform the sensitivity check. Refer to INITIALIZATION [05/2013 - ] .

   Standard range

   27 to 33 kg (59.5 to 72.8 lb)

NEXT → END