LEMON Manuals: Even more car manuals for everyone
Home >> Scion >> 2013 >> xB Automatic Trans >> Repair and Diagnosis >> Body & Frame >> Windows >> Windshield / WINDOWGLASS (Service Information) >> Back Door Glass >> Installation >> Installation

Back Door Glass: Installation: Installation

  1. CLEAN BACK DOOR GLASS 
    Fig 1: Cleaning Outer Edge Of Glass
    GTY163597Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Using a scraper, remove the clips, dam and adhesive sticking to the back door glass.
    2. Clean the outer edge of the back door glass with a non-residue solvent.
      NOTE:
      • Do not touch the back door glass surface after cleaning it.
      • Even if using a new back door glass, clean the back door glass with a non-residue solvent.

      HINT: 

      Since the pin is for positioning the glass, there is no need to replace it with a new one when reusing the glass, even if damaged.

  2. CLEAN VEHICLE BODY 
    1. Clean and shape the contact surface of the vehicle body.
      Fig 2: Identifying Adhesive On Vehicle Body Contact Surface
      GTY121647Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Using a knife, cut away any rough adhesive on the contact surface of the vehicle body to ensure the appropriate surface shape.
        NOTE:

        Do not damage the vehicle body.

        HINT: 

        Leave as much adhesive on the vehicle body as possible.

      2. Clean the contact surface of the vehicle body with a shop rag or piece of cloth saturated with cleaner.

        HINT: 

        Clean the vehicle body even if all the adhesive has been removed.

  3. INSTALL NO. 1 BACK WINDOW GLASS SPACER 
    Fig 3: Identifying No. 1 Back Window Glass Spacer
    GTY159996Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Apply Primer G to the installation part of the No. 1 back window glass spacer.

      HINT: 

      If primer is applied to an area that is not specified, wipe off the primer with a non-residue solvent before it dries.

    2. Install the new spacer onto the glass as shown in the illustration.
      NOTE:
      • Allow the primer to dry for 3 minutes or more.
      • Throw away any leftover primer.
      • Do not apply too much primer.
  4. INSTALL NO. 2 BACK WINDOW GLASS SPACER 
    Fig 4: Identifying No. 2 Back Window Glass Spacer
    GTY159995Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Apply Primer G to the installation part of the No. 2 back window glass spacer.

      HINT: 

      If primer is applied to an area that is not specified, wipe off the primer with a non-residue solvent before it dries.

    2. Install the new spacer onto the glass as shown in the illustration.
      NOTE:
      • Allow the primer to dry for 3 minutes or more.
      • Throw away any leftover primer.
      • Do not apply too much primer.
  5. INSTALL BACK DOOR GLASS ADHESIVE DAM 
    1. Apply Primer G to the installation part of the back door glass adhesive dam.
      NOTE:
      • Allow the primer to dry for 3 minutes or more.
      • Throw away any leftover primer.
      • Do not apply too much primer.

      HINT: 

      If primer is applied to an area that is not specified, wipe off the primer with a non-residue solvent before it dries.

    2. Install 2 new back door glass adhesive dams as shown in the illustration.
      Fig 5: Identifying Back Door Glass Adhesive Dams
      GTY159821Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Specification

      Area Measurement
      a 7.0 mm (0.276 in.)
      b 8.5 mm (0.335 in.)
  6. INSTALL BACK WINDOW OUTSIDE MOULDING 
    1. Apply Primer G to the installation part of the back window outside moulding.
      NOTE:
      • Allow the primer to dry for 3 minutes or more.
      • Throw away any leftover primer.
      • Do not apply too much primer.

      HINT: 

      If an area other than that specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.

    2. Install a new back door glass outside moulding as shown in the illustration.
      Fig 6: Identifying Back Door Glass Moulding
      GTY163704Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Specification

      Area Measurement
      a 4.1 mm (0.161 in.)
  7. INSTALL BACK DOOR GLASS 
    Fig 7: Positioning Back Door Glass Onto Vehicle Body
    GTY162851Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Position the back door glass.
      1. Using suction cups, place the back door glass in the correct position.
      2. Check that the whole contact surface of the back door glass rim is perfectly even.
      3. Place matchmarks on the back door glass and vehicle body.
        NOTE:

        Check that the stoppers are attached to the vehicle body correctly.

        HINT: 

        When reusing the back door glass, check and correct the matchmark positions.

      4. Using suction cups, remove the back door glass.
    2. Using a brush, apply Primer M to the exposed part of the vehicle body.
      Fig 8: Identifying Primer M Correct Application Areas
      GTY162584Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:
      • Allow the primer to dry for 3 minutes or more.
      • Do not apply Primer M to the adhesive.
      • Throw away any leftover Primer M.
      • Do not apply too much Primer M.
    3. Using a brush or sponge, apply Primer G to the edge of the back door glass and contact surface.
      Fig 9: Identifying Primer G Correct Application Areas
      GTY162798Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:
      • Allow the primer to dry for 3 minutes or more.
      • Throw away any leftover Primer G.
      • Do not apply too much Primer G.

      HINT: 

      If Primer G is applied to any areas other than those specified, wipe off the primer with a clean shop rag or piece of cloth before it dries.

      Specification

      Area Measurement
      a 11.0 mm (0.433 in.)
      b 50.8 mm (2.000 in.)
      c 11.0 mm (0.433 in.)
    4. Apply adhesive.

      Adhesive

      Toyota Genuine Windshield Glass Adhesive or equivalent

      1. Cut off the tip of the cartridge nozzle, as shown in the illustration.
        Fig 10: Identifying Cartridge Nozzle Tip Dimensions
        GTY166250Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

        HINT: 

        After cutting off the tip, use all adhesive within the time indicated in the table below.

        Usage time frame

        Temperature Usage Time Frame
        35°C (95°F) 15 minutes
        20°C (68°F) 1 hour 40 minutes
        5°C (41°F) 8 hours
      2. Load the sealer gun with the cartridge.
      3. Apply adhesive to the back door glass, as shown in the illustration.
        Fig 11: Identifying Adhesive Correct Application Areas
        GTY162901Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

        Specification

        Area Measurement
        a 12.0 mm (0.472 in.)
        b 8.0 mm (0.315 in.)
        c 16.3 mm (0.642 in.)
        d 8.0 mm (0.315 in.)
        e 57.8 mm (2.276 in.)
        f 17.7 mm (0.697 in.)
    5. Install the back door glass onto the vehicle body.
      Fig 12: Positioning Back Door Glass Onto Vehicle Body
      GTY162851Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Using suction cups, position the back door glass so that the matchmarks are aligned. Press it in gently along the rim.
        NOTE:
        • Allow the primer to dry for 3 minutes or more.
        • Check that the stoppers are attached to the vehicle body correctly.
        • Check that the vehicle body and back door glass have a small gap between them.
      2. Gently press the front surface of the back door glass to ensure that the back door glass is securely fitted to the vehicle body.
      3. Using a scraper, remove any excessive or protruding adhesive.
        Fig 13: Using A Scraper To Remove Excessive Or Protruding Adhesive
        GTY165420Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

        HINT: 

        Apply adhesive onto the back door glass rim.

        NOTE:

        Do not to drive the vehicle within the time indicated in the table below.

        Minimum time

        Temperature Minimum time prior to driving vehicle
        35°C (95°F) 1 hour 30 minutes
        20°C (68°F) 5 hours
        5°C (41°F) 24 hours
  8. CHECK FOR LEAKAGE AND REPAIR 
    1. After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.
    2. If water leaks into the cabin, allow the water to dry and add adhesive.
    3. Remove the protective tape.
  9. INSTALL BACK DOOR TRIM UPPER PANEL ASSEMBLY  . Refer to INSTALLATION - Step 2
  10. INSTALL BACK DOOR TRIM BOARD ASSEMBLY  . Refer to REASSEMBLY - Step 13
  11. INSTALL REAR WIPER ARM AND BLADE ASSEMBLY  . Refer to INSTALLATION - Step 3
scientia non olet · About LEMON Manuals