LEMON Manuals: Even more car manuals for everyone
Home >> Scion >> 2013 >> tC Automatic Trans >> Repair and Diagnosis >> Engine Performance >> System >> Engine Control System (Diagnostic Codes (P0420-P1605)) >> SFI System >> DTC P050B: Cold Start Ignition Timing Performance >> Procedure

DTC P050B: Cold Start Ignition Timing Performance: Procedure

  1. CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P050B) 
    1. Connect the Techstream to the DLC3.
    2. Turn the ignition switch to ON.
    3. Turn the Techstream on.
    4. Enter the following menus: Powertrain / Engine / Trouble Codes.
    5. Read the DTCs.
      RESULT

      Result Proceed to
      P050B is output A
      P050B and other DTCs are output B

      HINT: 

      If any DTCs other than P050B are output, troubleshoot those DTCs first.

    B → See step   21 

    A: Go to next step 

  2. READ VALUE USING TECHSTREAM (FUEL TRIM) 

    HINT: 

    Calculate the total fuel trim values to check the characteristic deviation of the mass air flow meter.

    1. Connect the Techstream to the DLC3.
    2. Start the engine.
    3. Turn the Techstream on.
    4. Enter the following menus: Powertrain / Engine / Data List / All Data / Short FT #1 and Long FT #1.
    5. Read the values displayed on the Techstream.
    6. Add together the Short FT #1 and Long FT #1 values to obtain the total fuel trim.

      OK

      Total of Short FT #1 and Long FT #1 values is between -20% and 20%.

    NG → See step   5 

    OK: Go to next step 

  3. INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY 
    1. Check for deposits around the throttle valve and check the throttle valve condition.

      OK

      No deposits around throttle valve and throttle valve moves smoothly.

    OK → See step   14 

    NG → See step   4 

  4. REPAIR OR REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY 
    1. Repair or replace the throttle with motor body assembly. Refer to REMOVAL .

    NEXT → See step   14 

  5. CHECK PCV HOSE 
    1. Check the PCV hose connections. Refer to ON-VEHICLE INSPECTION - Step 2 .

      OK

      PCV hose is connected correctly and is not damaged.

    NG → See step   10 

    OK: Go to next step 

  6. CHECK AIR INDUCTION SYSTEM 
    1. Check the air induction system for vacuum leaks. Refer to ON-VEHICLE INSPECTION - Step 1 .

      OK

      No leak in the air induction system.

    NG → See step   11 

    OK: Go to next step 

  7. INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY 
    1. Visually check that the air cleaner filter element is not excessively contaminated with dirt or oil.

      OK

      The air cleaner filter element is not excessively contaminated with dirt or oil.

    NG → See step   12 

    OK: Go to next step 

  8. PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE VVT LINEAR) 
    1. Connect the Techstream to the DLC3.
    2. Start the engine.
    3. Turn the Techstream on.
    4. Warm up the engine.
    5. Turn the A/C on.
    6. Enter the following menus: Powertrain / Engine / Active Test / Control the VVT Linear (Bank 1).
    7. Check the engine speed while operating the camshaft timing oil control valve using the Techstream.

      OK

      Techstream Operation Specified Condition
      0% Normal engine speed
      100% Engine idles roughly or stalls

      HINT: 

      Refer to "Data List / Active Test" [VVT OCV Duty #1 and VVT Change Angle #1]. Refer to DATA LIST / ACTIVE TEST .

    NG → See step   13 

    OK: Go to next step 

  9. READ VALUE USING TECHSTREAM (MAF) 
    1. Connect the Techstream to the DLC3.
    2. Turn the ignition switch to ON.
    3. Turn the Techstream on.
    4. Enter the following menus: Powertrain / Engine / Data List / All Data / MAF and Coolant Temp.
    5. Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.
    6. Read MAF with the engine speed at 3000 rpm.

      Standard

      Between 8 gm/s and 22 gm/s (shift lever: N; A/C: Off).

    OK → See step   14 

    NG → See step   15 

  10. REPAIR OR REPLACE PCV HOSE 
    1. Repair or replace the PCV hose.

    NEXT → See step   14 

  11. REPAIR OR REPLACE AIR INDUCTION SYSTEM 
    1. Repair or replace the air induction system.

    NEXT → See step   14 

  12. REPLACE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY 
    1. Replace the air cleaner filter element sub-assembly.

    NEXT → See step   14 

  13. CHECK AND REPAIR VVT SYSTEM 
    1. Check and repair the VVT system.

    NEXT: Go to next step 

  14. CHECK WHETHER DTC OUTPUT RECURS 
    NOTE:

    In this operation, the engine must be cold (approximately the same temperature as the engine coolant temperature recorded in the freeze frame data).

    1. Connect the Techstream to the DLC3.
    2. Turn the ignition switch to ON.
    3. Turn the Techstream on.
    4. Clear the DTCs. Refer to DTC CHECK / CLEAR .
    5. Turn the ignition switch off.
    6. Turn the ignition switch to ON and turn the Techstream on.
    7. Enter the following menus: Powertrain / Engine / Data List / Coolant Temp.
    8. Check that the engine coolant temperature is between -10°C and 50°C (14 and 122°F)
    9. Start the engine and warm it up.
    10. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
    11. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
    12. Input the DTC: P050B.
    13. Check the DTC judgment result.
      RESULT

      Result Proceed to
      NORMAL (DTC is not output) A
      ABNORMAL (DTC P050B is output) B

    B → See step   15 

    A → See step   22 

  15. CHECK HARNESS AND CONNECTOR 
    1. Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter and ECM. Refer to ELECTRONIC CIRCUIT INSPECTION PROCEDURE .

      HINT: 

      Repair any problems.

    NEXT: Go to next step 

  16. CHECK WHETHER DTC OUTPUT RECURS 
    NOTE:

    In this operation, the engine must be cold (approximately the same temperature as the engine coolant temperature recorded in the freeze frame data).

    1. Connect the Techstream to the DLC3.
    2. Turn the ignition switch to ON.
    3. Turn the Techstream on.
    4. Clear the DTCs. Refer to DTC CHECK / CLEAR .
    5. Turn the ignition switch off.
    6. Turn the ignition switch to ON and turn the Techstream on.
    7. Enter the following menus: Powertrain / Engine / Data List / Coolant Temp.
    8. Check that the engine coolant temperature is between -10°C and 50°C (14 and 122°F)
    9. Start the engine and warm it up.
    10. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
    11. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
    12. Input the DTC: P050B.
    13. Check the DTC judgment result.
      RESULT

      Result Proceed to
      ABNORMAL (DTC P050B is output) A
      NORMAL (DTC is not output) B

    B → END 

    A: Go to next step 

  17. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM) 
    1. Disconnect the mass air flow meter connector.
    2. Disconnect the ECM connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      B2-5 (VG) - B30-94 (VG) Always Below 1 Ω
      B2-4 (E2G) - B30-117 (E2G) Always Below 1 Ω
      B2-5 (VG) or B30-94 (VG) - Body ground Always 10 kΩ or higher

    NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK: Go to next step 

  18. REPLACE MASS AIR FLOW METER SUB-ASSEMBLY 
    1. Replace the mass air flow meter sub-assembly. Refer to REMOVAL .

      HINT: 

      If the result of the inspection performed in step 9 indicated no problem, proceed to the next step without replacing the mass air flow meter sub-assembly.

    NEXT: Go to next step 

  19. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED 
    NOTE:

    In this operation, the engine must be cold (approximately the same temperature as the engine coolant temperature recorded in the freeze frame data).

    1. Connect the Techstream to the DLC3.
    2. Turn the ignition switch to ON.
    3. Turn the Techstream on.
    4. Clear the DTCs. Refer to DTC CHECK / CLEAR .
    5. Turn the ignition switch off.
    6. Turn the ignition switch to ON and turn the Techstream on.
    7. Enter the following menus: Powertrain / Engine / Data List / Coolant Temp.
    8. Check that the engine coolant temperature is between -10°C and 50°C (14 and 122°F).
    9. Start the engine and warm it up.
    10. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
    11. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
    12. Input the DTC: P050B.
    13. Check the DTC judgment result.
      RESULT

      Result Proceed to
      NORMAL (DTC is not output) A
      ABNORMAL (DTC P050B is output) B

    B → See step   20 

    A → END 

  20. REPLACE ECM. Refer to  REMOVAL 
  21. GO TO DTC CHART. Refer to  DIAGNOSTIC TROUBLE CODE CHART 
  22. CHECK FOR INTERMITTENT PROBLEMS. Refer to  CHECK FOR INTERMITTENT PROBLEMS 
scientia non olet · About LEMON Manuals