Operation Check

Fig 1: Identifying Window Lock Switch

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

HINT: 

Before performing the window lock switch operation check, make sure that the window lock switch is off (the switch is not pushed in).

1. Check that the front passenger side power window cannot be operated when the window lock switch of the multiplex network master switch is pressed.

   OK

   Operation of front passenger side power window is disabled.

   HINT: 

   Even when the window lock switch of the multiplex network master switch is pressed in, remote manual up and down and auto up and down functions can be operated.

2. Check that the front passenger side power window can be operated when the window lock switch is pressed again.

   OK

   Front passenger side power window can be operated.

1. Check that the driver side power window operates as follows:

   OK

   Multiplex Network Master Switch	Condition	Switch Operation	Power Window
   Driver side	Power switch on (IG)	Pulled halfway up	UP (Closes)
   		Pushed halfway down	DOWN (Opens)

2. Check that the front passenger side power window operates as follows:

   OK

   Power Window Regulator Switch	Condition	Switch Operation	Power Window
   Front passenger side	Power switch on (IG) Window lock switch off	Pulled halfway up	UP (Closes)
   		Pushed halfway down	DOWN (Opens)

1. Check that the driver side power window operates as follows:

   OK

   Multiplex Network Master Switch	Condition	Switch Operation	Power Window
   Driver side	Power switch on (IG)	Pulled up (One touch operation)	AUTO UP (Closes)
   		Pushed down (One touch operation)	AUTO DOWN (Opens)

2. Check that the front passenger side power window operates as follows:

   OK

   Power Window Regulator Switch	Condition	Switch Operation	Power Window
   Front passenger side	Power switch on (IG) Window lock switch off	Pulled up (One touch operation)	AUTO UP (Closes)
   		Pushed down (One touch operation)	AUTO DOWN (Opens)

1. Check that the front passenger side power window operates as follows:

   OK

   Multiplex Network Master Switch	Condition	Switch Operation	Power Window
   Front passenger side	Power switch on (IG) Window lock switch off	Pulled halfway up	UP (Closes)
   		Pushed halfway down	DOWN (Opens)

1. Check that the front passenger side power window operate as follows:

   OK

   Multiplex Network Master Switch	Condition	Switch Operation	Power Window
   Front passenger side	Power switch on (IG)	Pulled up (One touch operation)	AUTO UP (Closes)
   		Pushed down (One touch operation)	AUTO DOWN (Opens)

1. Check that all the power windows can be operated with the multiplex network master switch assembly after the power switch is turned off.
2. After turning the power switch off, check if the power window regulator switch can operate the front passenger side power window.
3. Check that the key-off operation function does not operate after the driver door is opened and closed.
4. Check that all the power windows cannot be operated after more than approximately 45 seconds have elapsed since the power switch is turned off.

1. Check the basic function.
   WARNING:

   Do not put your fingers between the door frame and door glass to check functions. Also, prevent any part of your body from being caught during inspection.

   HINT: 

   The jam protection function is operative during both AUTO UP and MANUAL UP operation while the EV control system is started or the power switch on (IG), and also approximately 45 seconds after the power switch is turned off.

   1. Fully open the window.
   2. Set a thick book wrapped with a piece of cloth near the power window fully closed position.
   3. Operate the AUTO UP or MANUAL UP function to check that the power window goes down immediately after the book is caught between the window and door frame, and stops when the opening reaches approximately 200 mm (7.87 in.).

      HINT: 

      The power window moves down approximately 125 mm (4.93 in.). However, when the opening does not reach 200 mm (7.87 in.), the power window continues to go down until the opening reaches 200 mm (7.87 in.) or until approximately 5 seconds have elapsed.

   4. While the power window is moving down, check that the door glass cannot be moved up even when the power window regulator switch is used.

1. Check the LED illumination.
   1. Check that the LED located on the multiplex network master switch assembly illuminates when the power switch is turned on (IG).

1. Check that the LED located on the power window regulator switch illuminates when the power switch on (IG) and the window lock switch is set to the UNLOCK position.