Front Seat Assembly: Installation

CAUTION: Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (See PRECAUTION ).

HINT:

The procedure described below is for the driver side. Use the same procedure for both front passenger and driver sides, unless otherwise specified.

INSTALL FRONT SEAT ASSEMBLY LH
NOTE: Follow the procedure described below in order to prevent the seat tracks from locking separately.
1. Insert the 2 locating pins through the 2 body holes, place the front seat in the most forward position and make sure that the inner and outer seat tracks are locked securely.
2. Install bolt 1 and then bolt 2 onto the rear side.
  Torque: 37 N*m (375 kgf*cm, 27 ft.*lbf)
3. Move the front seat to the most rearward position, and then make sure that the inner and outer seat tracks are securely locked.
4. Install bolt 3 and then bolt 4 onto the rear side.
  Torque: 37 N*m (375 kgf*cm, 27 ft.*lbf)
5. Make sure that the inner and outer seat tracks lock simultaneously after the seat is moved.
  HINT:
  
  If the inner and outer seat tracks do not lock simultaneously, adjust the seat tracks by loosening the bolts.
  
  Fig 1: Installing Front Seat Assembly LH
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
6. Connect the airbag connector.
7. Connect the buckle switch connector.
8. Engage the wiring harness clamp.
  
  Fig 2: Locating Airbag Connector And Buckle Switch Connector
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL FRONT SEAT ASSEMBLY RH
NOTE: Follow the procedure described below in order to prevent the seat tracks from locking separately.
1. Insert the 2 locating pins through the 2 body holes, place the front seat in the most forward position and make sure that the inner and outer seat tracks are locked securely.
2. Install bolt 1 and then bolt 2 onto the rear side.
  Torque: 37 N*m (375 kgf*cm, 27 ft.*lbf)
3. Move the front seat to the most rearward position, and then make sure that the inner and outer seat tracks are securely locked.
4. Install bolt 3 and then bolt 4 onto the rear side.
  Torque: 37 N*m (375 kgf*cm, 27 ft.*lbf)
5. Make sure that the inner and outer seat tracks lock simultaneously after the seat is moved.
  
  Fig 3: Installing Front Seat Assembly RH
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  
  HINT:
  
  If the inner and outer seat tracks do not lock simultaneously, adjust the seat tracks by loosening the bolts.
6. Connect the airbag connector.
7. Connect the front seat wire connector.
8. Engage the wiring harness clamp.
  
  Fig 4: Locating Airbag Connector And Front Seat Wire Connector
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL SEAT TRACK INNER BRACKET COVER
1. Engage the claw and install the seat track inner bracket cover.
  
  Fig 5: Identifying Seat Track Inner Bracket Cover Claw
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL SEAT TRACK COVER
1. Engage the claw and install the seat track cover.
2. Tighten the screw.
  
  Fig 6: Locating Seat Track Cover Screw
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL FRONT SEAT HEADREST ASSEMBLY
1. Push in the 2 lock buttons of the front seat headrest supports and install the 2 front seat headrests.
Fig 7: Identifying Lock Button Of Front Seat Headrest
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
Torque: 5.4 N*m (55 kgf*cm, 48 in.*lbf)
INSPECT SRS WARNING LIGHT
(See DIAGNOSIS SYSTEM )