LEMON Manuals: Even more car manuals for everyone
Home >> Scion >> 2008 >> xB Automatic >> Repair and Diagnosis >> Transmission >> Automatic Trans >> U241E Automatic Transaxle >> Valve Body Assembly >> Inspection

Valve Body Assembly: Inspection

  1. INSPECT SHIFT SOLENOID VALVE SL1 
    1. Measure the resistance.

      Standard resistance 

      TESTER CONNECTION SPECIFIED CONDITION CHART

      Tester Connection Condition Specified Condition
      1 - 2 20°C (68°F) 5.0 to 5.6 Ω
      Fig 1: Inspecting Shift Solenoid Valve SL1
      G05388073Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Connect the positive (+) battery lead with a 21 W bulb to terminal 2 and the negative (-) battery lead to terminal 1 of the solenoid valve connector, and check the operation of the valve.
      NOTE: While using the battery during the inspection, do not bring the positive and negative tester probes too close to each other as a short circuit may occur.

      OK: 

      The solenoid makes an operating sound. 

      If the resistance is not as specified, replace the shift solenoid valve SL1.

  2. INSPECT SHIFT SOLENOID VALVE SL2 
    1. Measure the resistance.

      Standard resistance 

      TESTER CONNECTION SPECIFIED CONDITION CHART

      Tester Connection Condition Specified Condition
      1-2 20°C (68°F) 5.0 to 5.6 Ω
      Fig 2: Inspecting Shift Solenoid Valve SL2
      G05388074Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Connect the positive (+) battery lead with a 21 W bulb to terminal 2 and the negative (-) battery lead to terminal 1 of the solenoid valve connector, and check the operation of the valve.
      NOTE: While using the battery during the inspection, do not bring the positive and negative tester probes too close to each other as a short circuit may occur.

      OK: 

      The solenoid makes an operating sound. 

      If the resistance is not as specified, replace the shift solenoid valve SL2.

  3. INSPECT SHIFT SOLENOID VALVE SLT 
    1. Measure the resistance.

      Standard resistance 

      TESTER CONNECTION SPECIFIED CONDITION CHART

      Tester Connection Condition Specified Condition
      1-2 20°C (68°F) 5.0 to 5.6 Ω
      Fig 3: Inspecting Shift Solenoid Valve SLT
      G05388075Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Connect the positive (+) battery lead with a 21 W bulb to terminal 2 and the negative (-) battery lead to terminal 1 of the solenoid valve connector, and check the operation of the valve.
      NOTE: While using the battery during the inspection, do not bring the positive and negative tester probes too close to each other as a short circuit may occur.

      OK: 

      The solenoid makes an operating sound. 

      If the resistance is not as specified, replace the shift solenoid valve SLT.

  4. INSPECT SHIFT SOLENOID VALVE DSL 
    1. Measure the resistance.

      Standard resistance 

      TESTER CONNECTION SPECIFIED CONDITION CHART

      Tester Connection Condition Specified Condition
      Solenoid Connector (DSL) - Solenoid Body (DSL) 20°C (68°F) 11 to 13Ω
      Fig 4: Inspecting Shift Solenoid Valve DSL
      G05388076Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Connect the positive (+) battery lead to the terminal of the solenoid connector, and the negative (-) battery lead to the solenoid body, and check the operation of the valve.
      NOTE: While using the battery during the inspection, do not bring the positive and negative tester probes too close to each other as a short circuit may occur.

      OK: 

      The solenoid makes an operating sound. 

      If the resistance is not as specified, replace the shift solenoid valve DSL.

  5. INSPECT SHIFT SOLENOID VALVE S4 
    1. Measure the resistance.

      Standard resistance 

      TESTER CONNECTION SPECIFIED CONDITION CHART

      Tester Connection Condition Specified Condition
      Solenoid Connector (S4) - Solenoid Body (S4) 20°C (68°F) 11 to 15Ω
      Fig 5: Inspecting Shift Solenoid Valve S4
      G05388077Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Connect the positive (+) battery lead to the terminal of the solenoid connector, and the negative (-) battery lead to the solenoid body, and check the operation of the valve.
      NOTE: While using the battery during the inspection, do not bring the positive and negative tester probes too close to each other as a short circuit may occur.

      OK: 

      The solenoid makes an operating sound. 

      If the resistance is not as specified, replace the shift solenoid valve S4.

scientia non olet · About LEMON Manuals