Wiring Systems & Electrical Power Management

• Specifications
  • Fastener Tightening Specifications
• Diagnostic Information and Procedures
  • Passenger Car Zoning
  • Electrical Symbols
  • General Electrical Diagnosis Procedures
    • Basic Knowledge Required
  • Checking Aftermarket Accessories
  • Circuit Testing
  • Using Connector Test Adapters
  • Probing Electrical Connectors
    • Notes
    • Frontprobe
      • Notes
      • Backprobe
  • Troubleshooting with a Digital Multimeter
  • Troubleshooting with a Test Lamp
  • Using Fused Jumper Wires
    • Tools Required
  • Measuring Voltage
  • Measuring Voltage Drop
  • Measuring Frequency
  • Testing for Continuity
    • Notes
    • With a DMM
    • With a Test Lamp
  • Testing for Short to Ground
    • Notes
    • With a DMM
    • With a Test Lamp
    • Fuse Powering Several Loads
  • Testing for a Short to Voltage
  • Testing for Intermittent Conditions and Poor Connections
    • Tools Required
    • Testing for Proper Terminal Contact
    • Round Wire Connectors
  • Inducing Intermittent Fault Conditions
    • Notes
    • Salt Water Spray
    • High Temperature Conditions
      • Tools Required
    • Low Temperature Conditions
  • Testing for Electrical Intermittents
  • Scan Tool Snapshot Procedure
  • Circuit Protection - Fuses
  • Circuit Protection - Circuit Breakers
  • Circuit Protection - Fusible Links
    • Notes
    • Repairing a Fusible Link
  • Wiring Repairs
  • Repairing Damaged Wire Insulation
  • Splicing Copper Wire Using Splice Sleeves
  • Splicing Twisted or Shielded Cable
  • SIR/SRS Wiring Repairs
    • Tools Required
      • Notes
      • SIR/SRS Connector (Plastic Body and Terminal Metal Pin) Repair
    • SIR/SRS Wire Pigtail Repair
    • SIR/SRS Wire Repair
    • Connector Position Assurance (CPA)
    • Terminal Position Assurance (TPA)
  • Connector Repairs
  • Connector Position Assurance Locks
  • Terminal Position Assurance Locks
  • Push to Seat Connectors
    • Terminal Removal Procedure
    • Terminal Installation Procedure
  • Pull to Seat Connectors
    • Terminal Removal Procedure
    • Terminal Repair Procedure
  • Micro-Pack 100W Connectors
    • Tools Required
    • Removal Procedure
    • Repair Procedure
    • Replacement Procedure
  • Micro .64 Connectors
    • Tools Required
    • Removal Procedure
    • Repair Procedure
• Schematic and Routing Diagrams
  • Power and Grounding Schematic Icons
  • Power Distribution Schematics
  • Ground Distribution Schematics
  • Cigar Lighter/Auxiliary Outlets Schematics
  • Harness Routing Views
• Component Locator
  • Master Electrical Component List
  • Power and Grounding Component Views
  • Electrical Center Identification Views
    • Fuse Block - Underhood Label
    • Fuse Block - Underhood Top View
    • Fuse Block - Underhood Bottom View
      • Notes
      • Fuse Block - I/P Left Label
    • Fuse Block - I/P Left Top View
      • Notes
      • Fuse Block - I/P Right Label
    • Fuse Block - I/P Right Top View
  • Power and Grounding Connector End Views
  • Inline Harness Connector End Views
  • Splice Pack Connector End Views
• Repair Instructions
  • Relay Replacement (Within an Electrical Center)
    • Removal Procedure
    • Installation Procedure
  • Underhood Electrical Center or Junction Block Replacement
    • Removal Procedure
    • Installation Procedure
  • Instrument Panel Electrical Center or Junction Block Replacement
    • Removal Procedure
    • Installation Procedure
• Special Tools and Equipment
  • Special Tools