LEMON Manuals: Even more car manuals for everyone
Home >> Saturn >> 2005 >> Ion Red Line >> Repair and Diagnosis >> External Pages >> Different car >> Section 15 (Cruise Control System) >> Diagnostic Information and Procedures >> DTC P0565 >> Test Description

Test Description

WARNING: This page is about a different car, the 2004 Saturn Ion Red Line, 2004 Saturn Ion 3, 2004 Saturn Ion 2, and 2004 Saturn Ion 1. However, it is still accessible from the selected car via links, so may be relevant.

The number below refers to the step number on the diagnostic table.

  1. 8:  This vehicle is equipped with a ECM which utilizes an electrically erasable programmable read-only memory (EEPROM). When the ECM is replaced, the new ECM must be programmed.
DTC P0565

Step Action Yes No
Connector End View References:  Cruise Control Connector End Views  
1 Did you perform the Diagnostic System Check - Cruise Control? Go to Step 2  Go to Diagnostic System Check - Cruise Control (2.2L)  or Diagnostic System Check - Cruise Control (2.0L) 
2
  1. Install a scan tool.
  2. Start the engine.
  3. Cruise switch OFF.
  4. With a scan tool, monitor the DTC information for DTC P0565 in the ECM.
Is DTC P0565 active?		 Go to Step 3  Go to Step 9 
3
  1. Turn OFF the ignition.
  2. Disable the SIR system. Refer to SIR Disabling and Enabling Zones in SIR.
  3. Remove Cruise On/Off switch. Refer to Steering Wheel Control Switch Assembly Replacement in Steering Wheel and Column.
  4. Disconnect Cruise On/Off switch harness connector.
  5. Start the engine.
  6. With a scan tool, monitor the DTC information for DTC P0565 in the ECM.
Is DTC P0565 active?		 Go to Step 4  Go to Step 8 
4
  1. Turn OFF the ignition.
  2. Disconnect SIR roll connector. Refer to Inflatable Restraint Steering Wheel Module Coil Replacement in SIR.
  3. Start the engine.
  4. With a scan tool, monitor the DTC information for DTC P0565 in the ECM.
Is DTC P0565 active?		 Go to Step 5  Go to Step 7 
5 Test the Cruise Control Set/Coast and Resume/Accelerate Switch Signal circuit for a short to voltage. Refer to Circuit Testing andWiring Repairs in Wiring Systems.
Did you find and correct the condition?		 Go to Step 13  Go to Step 6 
6
IMPORTANT: The replacement engine control module (ECM) must be programmed.
Replace ECM. Refer to Engine Control Module (ECM) Replacement in Engine Controls - 2.2L (L61).Did you complete the repair?		 Go to Step 13  -
7 Replace the SIR roll connector. Refer to Inflatable Restraint Steering Wheel Module Coil Replacement in SIR.
Did you complete the repair?		 Go to Step 13  -
8  Replace cruise On/Off switch. Refer to Steering Wheel Control Switch Assembly Replacement in Steering Wheel and Column.
Did you complete the repair?		 Go to Step 13  -
9
  1. Start the engine.
  2. With a scan tool, monitor the DTC information for DTC P0565 in the ECM while holding cruise control switch ON for 3 seconds.
Is DTC P0565 active?		 Go to Step 8  Go to Step 10 
10
  1. Start the engine.
  2. Cruise control switch ON.
  3. With a scan tool, monitor the DTC information for DTC P0565 in the ECM while depressing SET/COAST for 3 seconds.
Is DTC P0565 active?		 Go to Step 12  Go to Step 11 
11
  1. Start the engine.
  2. Cruise control switch ON.
  3. With a scan tool, monitor the DTC information for DTC P0565 in the ECM while depressing RES/ACCEL for 3 seconds.
Is DTC P0565 active?		 Go to Step 12  Go to Diagnostic Aids
12 Replace the Set/Coast/Resume/Accel switch. Refer to Steering Wheel Control Switch Assembly Replacement in Steering Wheel and Column.
Did you complete the replacement?		 Go to Step 13  -
13
  1. Use a scan tool in order to clear the DTC.
  2. Operate the vehicle within the conditions for Running the DTC as specified in the supporting text.
Does the DTC reset?		 Go to Step 2  System OK
scientia non olet · About LEMON Manuals