LEMON Manuals: Even more car manuals for everyone
Home >> Saab >> 2010 >> 9-5 >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Communication Devices >> Bus And Diagnostics Communication >> Technical data >> Electronic Brake Control Module Scan Tool Information >> Electronic Brake Control Module Scan Tool Data Parameters

Electronic Brake Control Module Scan Tool Data Parameters

Parameter System State Expected Value Description
Operating Conditions:  Ignition ON
ABS Pump Motor Voltage - 0 V The scan tool displays the commanded pump motor voltage.
Acceleration Sensor Longitudinal Signal - Varies The scan tool displays 0-5 V depending on the vehicle's longitudinal acceleration.
Antilock Braking System - OK The scan tool displays OK or Malfunction. Malfunction is displayed if there is an ABS malfunction.
Brake Fluid Level Sensor - OK The scan tool displays OK when the brake fluid is at correct level and Low when the brake fluid is low.
Brake Pedal Position Sensor Brake pedal released Inactive The scan tool displays Inactive or Active depending on the state of the brake pedal.
Brake pedal applied Active
Brake Pressure Sensor Brake pedal released 0-1 V The scan tool displays 0-5 V depending on the applied hydraulic brake pressure.
Brake pedal applied 1-5 V
Delivered Torque - varies The scan tool displays 0-100% depending on the how much torque the engine is delivering.
Dynamic Rear Proportioning Status - OK The scan tool displays OK or Malfunction. Malfunction is displayed if the EBCM disables the dynamic rear proportioning due to a fault.
Lateral Acceleration Signal - Varies The scan tool displays 0-5 V depending on the vehicle's lateral acceleration.
Left Front Inlet Solenoid Valve Feedback - Inactive The scan tool displays Inactive or Active. Active is displayed when the left front inlet solenoid valve is commanded ON.
Left Front Outlet Solenoid Valve Feedback - Inactive The scan tool displays Inactive or Active. Active is displayed when the left front outlet solenoid valve is commanded ON.
Left Front Wheel Speed Sensor - 0 km/h (0 MPH) The scan tool displays km/h (MPH) depending on the current speed of the left front wheel speed sensor.
Left Rear Inlet Solenoid Valve Feedback - Inactive The scan tool displays Inactive or Active. Active is displayed when the left rear inlet solenoid valve is commanded ON.
Left Rear Outlet Solenoid Valve Feedback - Inactive The scan tool displays Inactive or Active. Active is displayed when the left rear outlet solenoid valve is commanded ON.
Left Rear Wheel Speed Sensor - 0 km/h (0 MPH) The scan tool displays km/h (MPH) depending on the current speed of the left rear wheel speed sensor.
Panic Brake Assist Status - OK The scan tool displays OK or Malfunction. Malfunction is displayed if the EBCM disables the panic brake assist due to a fault.
Pump Motor Relay Feedback - Inactive The scan tool displays Inactive or Active. Active is displayed when the pump motor is commanded ON.
Primary Isolation Solenoid Valve Feedback - Inactive The scan tool displays Inactive or Active. Active is displayed when the isolation solenoid valve is commanded ON.
Primary Prime Solenoid Valve Feedback - Inactive The scan tool displays Inactive or Active. Active is displayed when the prime solenoid valve is commanded ON.
Requested Torque - varies The scan tool displays 0-100% depending on the how much torque is requested.
Right Front Inlet Solenoid Valve Feedback - Inactive The scan tool displays Inactive or Active. Active is displayed when the right front inlet solenoid valve is commanded ON.
Right Front Outlet Solenoid Valve Feedback - Inactive The scan tool displays Inactive or Active. Active is displayed when the right front outlet solenoid valve is commanded ON.
Right Front Wheel Speed Sensor - 0 km/h (0 MPH) The scan tool displays km/h (MPH) depending on the current speed of the right front wheel speed sensor.
Right Rear Inlet Solenoid Valve Feedback - Inactive The scan tool displays Inactive or Active. Active is displayed when the right rear inlet solenoid valve is commanded ON.
Right Rear Outlet Solenoid Valve Feedback - Inactive The scan tool displays Inactive or Active. Active is displayed when the right rear outlet solenoid valve is commanded ON.
Right Rear Wheel Speed Sensor - 0 km/h (0 MPH) The scan tool displays km/h (MPH) depending on the current speed of the right rear wheel speed sensor.
Secondary Isolation Solenoid Valve Feedback - Inactive The scan tool displays Inactive or Active. Active is displayed when the isolation solenoid valve is commanded ON.
Secondary Prime Solenoid Valve Feedback - Inactive The scan tool displays Inactive or Active. Active is displayed when the prime solenoid valve is commanded ON.
Steering Column Position Steering wheel in straight position -5 to +5° The scan tool displays °. This is the current position of the steering angle sensor.
Steering wheel turned left until stop 450-550°
Steering wheel turned right until stop -550 to - 450°
System Voltage - 11-14 V The scan tool displays V. This is the current battery voltage.
Traction Control Switch Traction control switch released Inactive The scan tool displays Inactive or Active depending on the traction control switch status.
Traction control switch pressed Active
Traction Control System - OK The scan tool displays OK or Malfunction. Malfunction is displayed if there is a traction control malfunction.
Vehicle Stability System - OK The scan tool displays OK or Malfunction. Malfunction is displayed if there is a stability control malfunction.
Vehicle Stability System Relay Feedback - Active The scan tool displays Inactive or Active. Inactive is displayed when stability control is disabled.
Vehicle Stability Enhancement System Switch Traction control switch released Inactive The scan tool displays Inactive or Active depending on the traction control switch status.
Traction control switch pressed Active
Yaw Rate Signal - Varies The scan tool displays 0-5 V depending on the vehicle's yaw rate.
scientia non olet · About LEMON Manuals