Specifications Index
9-5 SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | TECHNICAL DATA (AUTO) Or TECHNICAL DATA (A/C-HEATER) | ||
| Torque | TIGHTENING TORQUES | ||
| Axle Shaft Hub Nut | 170 Ft. Lbs. (230 Nm). Use New Nut. | ||
| Battery | BATTERY | ||
| Brakes | |||
| Bleeding Sequence | BLEEDING BRAKE SYSTEM | ||
| Disc Brakes | DISC BRAKE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Charging | |||
| Generator | GENERATOR SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | BELT TENSION CHECKING | ||
| Belt Routing | DRIVE BELT ROUTING | ||
| Engine Cooling | |||
| General Service Procedures | TECHNICAL DATA | ||
| Radiator Cap Pressure | NA | ||
| Thermostat R & I | |||
| 4-CYL | THERMOSTAT | ||
| V6 | THERMOSTAT | ||
| Water Pump R & I | |||
| 4-Cylinder | COOLANT PUMP (4-CYL) | ||
| V6 | COOLANT PUMP (V6) | ||
| Engine Mechanical | |||
| Compression | ENGINE COMPRESSION | ||
| Oil Pressure | |||
| 4-Cylinder | OIL PRESSURES | ||
| V6 | NA | ||
| Overhaul | |||
| 4-Cylinder | TECHNICAL DATA | ||
| V6 | TECHNICAL DATA | ||
| Torque | |||
| 4-Cylinder | TIGHTENING TORQUES | ||
| V6 | TIGHTENING TORQUES | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate Torque | |||
| 4-Cylinder | 59 Ft. Lbs. (80 Nm) | ||
| V6 | NA | ||
| Fuel System | |||
| Fuel Filter Location | At Right Front Side Of Fuel Tank | ||
| Fuel Filter R & I | FUEL FILTER | ||
| Pressure Release Procedure | Remove fuel pump fuse No. 15 while the engine is idling. Turn off ignition once engine has stopped. Install fuse No. 15. | ||
| Pressure Specifications | 43 psi (296 kPa) | ||
| Fuel Pressure Test Procedure | FUEL PRESSURE & FLOW TESTS | ||
| Ignition | |||
| Firing Order & Cylinder Identidication | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Routing) | NA | ||
| Spark Plugs | |||
| Type | SPARK PLUGS | ||
| Gap | SPARK PLUGS | ||
| Torque | 18.5-21.5 Ft. Lbs. (25-29 Nm) | ||
| Starting | |||
| Starter | STARTER SPECIFICATIONS | ||
| Torque | NA | ||
| Wheel Alignment | |||
| Alignment Specifications | SPECIFICATIONS | ||
| Torque | |||
| Front | TIGHTENING TORQUES (FRONT) . Also see specific procedure in FRONT SUSPENSION . | ||
| Rear | TIGHTENING TORQUES (REAR) . Also see specific procedure in REAR SUSPENSION . | ||
| Wheel & Tire | |||
| Lug Stud Torque | |||
| Aluminum Wheel | 81 Ft. Lbs. (110 Nm) | ||
| Steel Wheel | 37 Ft. Lbs. (50 Nm). After initial torque, turn each lug stud an additional 90 degrees, then turn each lug stud another 90 degrees, to a maximum of 81 ft. lbs. (110 Nm). | ||