Section 570 (Diagnostic Trouble Code Index DTC: Transfer Case Control Module (TCCM) -- Range Rover/L405)
WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2018 Land Rover Range Rover, 2017 Land Rover Range Rover, 2016 Land Rover Range Rover, 2015 Land Rover Range Rover, and 2014 Land Rover Range Rover. However, it is still accessible from the selected car via links, so may be relevant.
- Diagnostic Trouble Code Index DTC: Transfer Case Control Module (TCCM)
- Description And Operation
- Transfer Case Control Module (TCCM)
- DTC P0605-41: Internal Control Module Read Only Memory (ROM) Error - General checksum failure
- DTC P0605-43: Internal Control Module Read Only Memory (ROM) Error - Special memory failure
- DTC P062F-43: Internal Control Module EEPROM Error - Special memory failure
- DTC P062F-68: Internal Control Module EEPROM Error - Event information
- DTC P0666-11: Control Module Internal Temperature Sensor "A" Circuit - Circuit short to ground
- DTC P0666-12: Control Module Internal Temperature Sensor "A" Circuit - Circuit short to battery
- DTC P0666-29: Control Module Internal Temperature Sensor "A" Circuit - Signal invalid
- DTC P0666-64: Control Module Internal Temperature Sensor "A" Circuit - Signal plausibility failure
- DTC P080A-56: Clutch Position Not Learned - Invalid/incomplete configuration
- DTC P0810-04: Clutch Position Control Error - System internal failures
- DTC P0810-07: Clutch Position Control Error - Mechanical failures
- DTC P0810-28: Clutch Position Control Error - Signal bias level out of range/zero adjustment failure
- DTC P0810-46: Clutch Position Control Error - Calibration/parameter memory failure
- DTC P0810-56: Clutch Position Control Error - Invalid/incomplete configuration
- DTC P0810-62: Clutch Position Control Error - Signal compare failure
- DTC P0810-77: Clutch Position Control Error - Commanded position not reachable
- DTC P0810-78: Clutch Position Control Error - Alignment or adjustment incorrect
- DTC P0919-94: Gear Shift Position Control Error - Unexpected operation
- DTC P160C-45: Control Module Software Performance - Program memory failure
- DTC P160C-48: Control Module Software Performance - Supervision software failure
- DTC P160C-94: Control Module Software Performance - Unexpected operation
- DTC P170E-07: Clutch Delivered Torque Performance - Mechanical failures
- DTC P170E-92: Clutch Delivered Torque Performance - Performance or incorrect operation
- DTC P175B-00: Transfer Case Clutch Deteriorated - No sub type information
- DTC P183A-67: Range Change Mechanism Failure - Signal incorrect after event
- DTC P183A-77: Range Change Mechanism Failure - Commanded position not reachable
- DTC P186D-71: Clutch Actuator Stuck - Actuator stuck
- DTC P18A4-13: Motion/Position Sensor Power Circuit - Circuit open
- DTC P18A4-16: Motion/Position Sensor Power Circuit - Circuit voltage below threshold
- DTC P18A4-17: Motion/Position Sensor Power Circuit - Circuit voltage above threshold
- DTC P18A5-03: Motion/Position Sensor A Signal Circuit - FM (Frequency Modulated)/PWM (Pulse Width Modulated) failures
- DTC P18A5-11: Motion/Position Sensor A Signal Circuit - Circuit short to ground
- DTC P18A5-12: Motion/Position Sensor A Signal Circuit - Circuit short to battery
- DTC P18A5-13: Motion/Position Sensor A Signal Circuit - Circuit open
- DTC P18A5-37: Motion/Position Sensor A Signal Circuit - Signal frequency too high
- DTC P18A5-62: Motion/Position Sensor A Signal Circuit - Signal compare failure
- DTC P215A-62: Vehicle Speed/Wheel Speed Correlation - Signal compare failure
- DTC P215A-64: Vehicle Speed/Wheel Speed Correlation - Signal plausibility failure
- DTC P2787-98: Clutch Temperature Too High - Component or system over temperature
- DTC U0080-81: Vehicle Communication Bus F - Invalid serial data received
- DTC U0080-82: Vehicle Communication Bus F - Alive/sequence counter incorrect/not updated
- DTC U0080-83: Vehicle Communication Bus F - Value of signal protection calculation incorrect
- DTC U0080-87: Vehicle Communication Bus F - Missing message
- DTC U0080-88: Vehicle Communication Bus F - Bus off
- DTC U1000-02: Solid State Driver Protection Active - Driver Disabled - General signal failure
- DTC U1000-11: Solid State Driver Protection Active - Driver Disabled - Circuit short to ground
- DTC U1000-12: Solid State Driver Protection Active - Driver Disabled - Circuit short to battery
- DTC U1000-16: Solid State Driver Protection Active - Driver Disabled - Circuit voltage below threshold
- DTC U1000-17: Solid State Driver Protection Active - Driver Disabled - Circuit voltage above threshold
- DTC U1000-1C: Solid State Driver Protection Active - Driver Disabled - Circuit voltage out of range
- DTC U1000-49: Solid State Driver Protection Active - Driver Disabled - Internal electronic failure
- DTC U1000-4B: Solid State Driver Protection Active - Driver Disabled - Over temperature
- DTC U1000-56: Solid State Driver Protection Active - Driver Disabled - Invalid/incomplete configuration
- DTC U1000-62: Solid State Driver Protection Active - Driver Disabled - Signal compare failure
- DTC U1A4B-04: Control Module Processor B - System internal failures
- DTC U1A4B-16: Control Module Processor B - Circuit voltage below threshold
- DTC U1A4B-17: Control Module Processor B - Circuit voltage above threshold
- DTC U1A4B-1C: Control Module Processor B - Circuit voltage out of range
- DTC U1A4B-47: Control Module Processor B - Watchdog/safety microcontroller failure
- DTC U1A4B-48: Control Module Processor B - Supervision software failure
- DTC U1A4B-49: Control Module Processor B - Internal electronic failure
- DTC U1A4B-4B: Control Module Processor B - Over temperature
- DTC U1A4B-55: Control Module Processor B - Not configured
- DTC U1A4B-56: Control Module Processor B - Invalid/incomplete configuration
- DTC U1A4B-64: Control Module Processor B - Signal plausibility failure
- DTC U1A4B-84: Control Module Processor B - Signal below allowable range
- DTC U1A4B-92: Control Module Processor B - Performance or incorrect operation
- DTC U1A4B-9A: Control Module Processor B - Component or system operating conditions
- DTC U200C-4B: Control Module Internal Power C - Over temperature
- DTC U200C-64: Control Module Internal Power C - Signal plausibility failure
- DTC U200C-9A: Control Module Internal Power C - Component or system operating conditions
- DTC U2011-16: Motor - Circuit voltage below threshold
- DTC U2011-17: Motor - Circuit voltage above threshold
- DTC U2011-18: Motor - Circuit current below threshold
- DTC U2011-19: Motor - Circuit current above threshold
- DTC U2011-1D: Motor - Circuit current out of range
- DTC U2011-28: Motor - Signal bias level out of range/zero adjustment failure
- DTC U2011-41: Motor - General checksum failure
- DTC U2011-4B: Motor - Over temperature
- DTC U2011-56: Motor - Invalid/incomplete configuration
- DTC U2011-62: Motor - Signal compare failure
- DTC U2011-68: Motor - Event information
- DTC U2011-77: Motor - Commanded position not reachable
- DTC U2011-78: Motor - Alignment or adjustment incorrect
- DTC U2011-85: Motor - Signal above allowable range
- DTC U2011-86: Motor - Signal invalid
- DTC U2011-98: Motor - Component or system over temperature
- DTC U2011-9A: Motor - Component or system operating conditions
- DTC U2016-04: Control Module Main Software - System internal failures
- DTC U2016-06: Control Module Main Software - Algorithm based failures
- DTC U2016-47: Control Module Main Software - Watchdog/safety microcontroller failure
- DTC U2016-49: Control Module Main Software - Internal electronic failure
- DTC U2016-92: Control Module Main Software - Performance or incorrect operation
- DTC U201A-54: Control Module Main Calibration Data - Missing calibration
- DTC U2100-54: Initial Configuration Not Complete - Missing calibration
- DTC U2101-56: Control Module Configuration Incompatible - Invalid/incomplete configuration
- DTC U2300-54: Central Configuration - Missing calibration
- DTC U2300-55: Central Configuration - Not configured
- DTC U2300-56: Central Configuration - Invalid/incomplete configuration
- DTC U2300-64: Central Configuration - Signal plausibility failure
- DTC U3000-1C: Control Module - Circuit voltage out of range
- DTC U3000-42: Control Module - General memory failure
- DTC U3000-4A: Control Module - Incorrect component installed
- DTC U3000-4B: Control Module - Over temperature
- DTC U3000-92: Control Module - Performance or incorrect operation
- DTC U3000-94: Control Module - Unexpected operation
- DTC U3000-98: Control Module - Component or system over temperature
- DTC U3006-13: Control Module Input Power "A" - Circuit open
- DTC U3006-16: Control Module Input Power "A" - Circuit voltage below threshold
- DTC U3006-17: Control Module Input Power "A" - Circuit voltage above threshold
- DTC U3006-85: Control Module Input Power "A" - Signal above allowable range
- DTC U3012-04: Control Module Improper Wake-up Performance - System internal failures
- DTC U3012-1C: Control Module Improper Wake-up Performance - Circuit voltage out of range
- DTC U3012-41: Control Module Improper Wake-up Performance - General checksum failure
- DTC U3012-48: Control Module Improper Wake-up Performance - Supervision software failure
- DTC U3012-92: Control Module Improper Wake-up Performance - Performance or incorrect operation
- DTC U3012-94: Control Module Improper Wake-up Performance - Unexpected operation
- DTC U3012-96: Control Module Improper Wake-up Performance - Component internal failure
- Description And Operation