LEMON Manuals: Even more car manuals for everyone
Home >> Pontiac >> 2008 >> Solstice Base, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 359 (Antilock Brake System With Traction Control System & Stability Control System) >> Repair Instructions >> Brake Pressure Modulator Valve Assembly Replacement >> Removal Procedure

Removal Procedure

WARNING: This page is about a different car, the 2010 Saturn Sky and 2010 Pontiac Solstice. However, it is still accessible from the selected car via links, so may be relevant.
WARNING: Refer to Brake Fluid Irritant Warning .
CAUTION: Refer to Brake Fluid Effects on Paint and Electrical Components Caution .
CAUTION: Always connect or disconnect the wiring harness connector from the EBCM/EBTCM with the ignition switch in the OFF position. Failure to observe this precaution could result in damage to the EBCM/EBTCM.
NOTE: This procedure applies to vehicles equipped with RPO JL4. The electronic brake control module (EBCM) and the brake pressure modulator valve (BPMV) must be replaced as an assembly and cannot be separated.
  1. Turn the ignition switch to the OFF position.
  2. Clean the brake pressure modulator assembly area of any accumulated dirt and foreign material.
    3. Fig 1: View Of Brake Fluid Level Indicator Switch & Vacuum Brake Booster Vacuum Sensor Electrical Connectors
    GM1859458Courtesy of GENERAL MOTORS CORP.
  3. Disconnect the brake fluid level indicator switch electrical connector.
  4. Disconnect the vacuum brake booster vacuum sensor electrical connector.
    5. Fig 2: View Of Master Cylinder Wiring Harness & Nuts
    GM1859462Courtesy of GENERAL MOTORS CORP.
  5. Release the wiring harness retainer from the master cylinder mounting stud and position the wiring harness downward.
  6. Remove and discard the 2 master cylinder nuts.
  7. If equipped, disconnect the clutch master cylinder hose from the brake master cylinder reservoir.

    Cap the brake fluid reservoir outlet and plug the clutch master cylinder hose inlet to prevent brake fluid loss and contamination.

    8. Fig 3: View Of Master Cylinder Brake Pipe Fittings
    GM1859463Courtesy of GENERAL MOTORS CORP.
  8. Remove the 2 master cylinder brake pipe fittings from the brake modulator assembly.

    Cap the brake pipe fittings and plug the BPMV inlet ports to prevent brake fluid loss and contamination.

  9. Remove the brake master cylinder and master cylinder brake pipes as an assembly.
    10. Fig 4: View Of Rear Brake Pipe Fittings, Front Brake Pipe Fittings & EBCM Electrical Connector
    GM1859741Courtesy of GENERAL MOTORS CORP.
  10. Remove the 2 rear brake pipe fittings (1) from the brake modulator assembly.

    Cap the brake pipe fittings to prevent brake fluid loss and contamination.

  11. Remove the 2 front brake pipe fittings (2) from the brake modulator assembly.

    Cap the brake pipe fittings to prevent brake fluid loss and contamination.

  12. Lift the locking tabs on the lower edge of the EBCM electrical connector (3) and disconnect the electrical connector.
  13. Position the EBCM electrical connector and the wiring harness toward the front of the vehicle.
    14. Fig 5: Locating Upper & Lower BPMV Bracket Bolts & Brake Modulator Bracket Assembly
    GM1859743Courtesy of GENERAL MOTORS CORP.
  14. Remove the 2 upper brake modulator assembly bracket bolts (1).
  15. Loosen, but do not remove the lower BPMV bracket bolt (2).
  16. Remove the brake modulator and bracket assembly (3).
    17. Fig 6: View Of BPMV Bracket & Bolt
    GM1859744Courtesy of GENERAL MOTORS CORP.
  17. Remove the brake modulator assembly bolt.
  18. Carefully separate the BPMV from the bracket. Do not pry against the accumulator covers on the underside of the brake modulator assembly.
scientia non olet · About LEMON Manuals