LEMON Manuals: Even more car manuals for everyone
Home >> Pontiac >> 2007 >> Vibe Automatic >> Repair and Diagnosis >> Engine Performance >> System >> Engine Control System & Fuel System - DTC P2195 To DTC P2A00 >> DTC P2419 >> Test Description

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. 5:  If you are at this diagnostic table because you were sent here from DTC P2401 or P2402, go to Step 11. If only DTC P2419 was set, go to Step 11. If you had a DTC P2401 or P2402 set with a P2419, go perform the P2401 or P2402 diagnostic procedure before continuing in this diagnostic table.
  2. 15:  This step uses the EVAP Service Bay test in order to verify the correct operation of the EVAP vent solenoid, the EVAP purge solenoid, and the EVAP vacuum leak pump. Using the Service Bay test also tests for leaks by sealing the system and monitoring the FTP sensor.
DTC P2419

Step Action Values Yes No
Schematic Reference:  Engine Controls Schematics 
Connector End View Reference:  Powertrain Control Module Connector End Views  or  Engine Controls Connector End Views 
1 Did you perform the Diagnostic System Check - Vehicle? - Go to Step 2  Go to Diagnostic System Check - Vehicle
2
  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. Disconnect the electrical connector of the evaporative emission (EVAP) vacuum leak pump assembly.
  4. Connect a test lamp across the EVAP vent solenoid control circuit and the ignition positive voltage circuit.
  5. Command the EVAP vent solenoid ON and OFF several times with the scan tool. Refer to Scan Tool Output Controls .
Did the test lamp illuminate ON and OFF as commanded by the scan tool?		 - Go to Step 3  Go to Step 6 
3
  1. Remove the EVAP vacuum leak pump assembly. Refer to Evaporative Emission System Vacuum Leak Pump Replacement .
  2. Inspect the operation of the EVAP vent solenoid located in the vacuum pump assembly. Refer to Evaporative Emission Control System Diagnosis .
  3. Replace the part as necessary.
Did you find and correct the condition?		 - Go to Step 15  Go to Step 4 
4
  1. Inspect the EVAP filter for blockage or restrictions. Refer to Evaporative Emission Canister Filter Replacement .
  2. Inspect the EVAP vent pipe for a blockage or restriction.
  3. Repair or replace as necessary.
Did you find and correct the condition?		 - Go to Step 15  Go to Step 5 
5  If a DTC P2401 or P2402 was also set, did you already perform the applicable diagnostic procedure? - Go to Step 11  Go to DTC P2401  or DTC P2402 
6 Was the test lamp always illuminated? - Go to Step 10  Go to Step 7 
7
  1. Turn ON the ignition, with the engine OFF.
  2. Measure the voltage of the vent solenoid ignition positive voltage circuit.
Is the voltage at the specified value?		 B+ Go to Step 9  Go to Step 8 
8 Repair the open in the vent solenoid ignition positive voltage circuit. Refer to Wiring Repairs .
Did you complete the repair?		 - Go to Step 15  -
9
  1. Test for an open in the vent solenoid control circuit.
  2. Repair as necessary. Refer to Wiring Repairs .
Did you find and correct the condition?		 - Go to Step 15  Go to Step 13 
10
  1. Test for a short to ground in the vent solenoid control circuit.
  2. Repair as necessary. Refer to Wiring Repairs .
Did you find and correct the condition?		 - Go to Step 15  Go to Step 14 
11
  1. Test for intermittent and for poor electrical connection at the EVAP vacuum leak pump assembly. Refer to Testing for Intermittent Conditions and Poor Connections .
  2. Repair as necessary. Refer to Wiring Repairs and Connector Repairs .
Did you find and correct the condition?		 - Go to Step 15  Go to Step 12 
12 Replace the EVAP vacuum leak pump assembly. Refer to Evaporative Emission System Vacuum Leak Pump Replacement .
Did you complete the replacement?		 - Go to Step 15  -
13
  1. Inspect for intermittent and for poor electrical terminal connections at the powertrain control module (PCM). Refer to Testing for Intermittent Conditions and Poor Connections .
  2. Repair as necessary. Refer to Wiring Repairs and Connector Repairs .
Did you find and correct the condition?		 - Go to Step 15  Go to Step 14 
14 Replace the PCM. Refer to Control Module References for replacement, setup, and programming.
Did you complete the replacement?		 - Go to Step 15  -
15 
  1. Use the scan tool in order to clear the DTCs.
  2. Turn OFF the ignition for 30 seconds.
  3. Turn ON the ignition, with the engine OFF.
  4. Perform the EVAP service bay test with the scan tool. Refer to EVAP Service Bay Test in Service Bay Test .
Is DTC P2419 set in Last Test Failed?		 - Go to Step 2  Go to Step 16 
16
  1. Check for any other EVAP DTCs in Last Test Failed.
  2. Observe the Capture Info with a scan tool.
Are there any DTCs that have not been diagnosed?		 - Go to Diagnostic Trouble Code (DTC) List - Vehicle System OK
scientia non olet · About LEMON Manuals