Specifications Index
G6 SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | REFRIGERANT SYSTEM CAPACITIES | ||
| Torque | |||
| Automatic | FASTENER TIGHTENING SPECIFICATIONS | ||
| Manual | FASTENER TIGHTENING SPECIFICATIONS | ||
| Axle Nut/Hub Nut | 159 Ft. Lbs. (215 N.m) | ||
| Battery | BATTERY USAGE | ||
| Brakes | |||
| Bleeding Sequence | RR, LF, LR, RF | ||
| Disc Brakes | |||
| Service Specifications | DISC BRAKE COMPONENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Drum Brakes | NA | ||
| Charging | |||
| Generator | GENERATOR USAGE | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | NA | ||
| Belt Routing | |||
| 2.4L | See appropriate figure under DRIVE BELT REPLACEMENT . | ||
| 3.5L | See figure under DRIVE BELT REPLACEMENT . | ||
| 3.9L | See appropriate figure under DRIVE BELT REPLACEMENT (COUPE) or DRIVE BELT REPLACEMENT (CONVERTIBLE) . | ||
| Engine Cooling | |||
| General Service Specifications | COOLING SYSTEM DESCRIPTION AND OPERATION | ||
| Radiator Cap Pressure | Radiator cap pressure is stamped on cap. | ||
| Thermostat R & I | |||
| 2.4L | THERMOSTAT REPLACEMENT (2.4L) | ||
| 3.5L | THERMOSTAT REPLACEMENT (3.5L) | ||
| 3.9L | THERMOSTAT REPLACEMENT (3.9L) | ||
| Water Pump R & I | |||
| 2.4L | WATER PUMP REPLACEMENT (2.4L) | ||
| 3.5L | WATER PUMP REPLACEMENT (3.5L) | ||
| 3.9L | WATER PUMP REPLACEMENT (3.9L) | ||
| Engine Mechanical | |||
| 2.4L | |||
| Compression | ENGINE COMPRESSION TEST | ||
| Oil Pressure | 50-80 psi (344.75-551.60 kPa) at 1,000 RPM | ||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| 3.5L | |||
| Compression | ENGINE COMPRESSION TEST | ||
| Oil pressure | 30-45 psi (207-310 kPa) at 1,850 RPM | ||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| 3.9L | |||
| Compression | ENGINE COMPRESSION TEST | ||
| Oil pressure | 30-45 psi (207-310 kPa) at 1,850 RPM | ||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive PlateTorque | |||
| 2.4L | |||
| First Pass | 39 Ft. Lbs. (53 N.m) | ||
| Final Pass | 25 degrees | ||
| 3.5L, 3.9L | 52 Ft. Lbs. (70 N.m) | ||
| Fuel System | |||
| 2.4L | |||
| Pressure Specification | 50-60 psi (345-414 kPa) | ||
| Fuel Pressure Test Procedure | FUEL SYSTEM DIAGNOSIS | ||
| Fuel Filter Location | Fuel strainer attaches to lower end of fuel sender. | ||
| Fuel Filter R & I | FUEL SENDER ASSEMBLY REPLACEMENT | ||
| 3.5L | |||
| Pressure Specification | 50-60 psi (384-425 kPa) | ||
| Fuel Pressure Test Procedure | FUEL SYSTEM DIAGNOSIS | ||
| Fuel Filter Location | Fuel strainer attaches to lower end of fuel sender. | ||
| Fuel Filter R & I | FUEL SENDER ASSEMBLY REPLACEMENT | ||
| 3.9L | |||
| Pressure Specification | 50-60 psi (345-414 kPa) | ||
| Fuel Pressure Test Procedure | FUEL SYSTEM DIAGNOSIS | ||
| Fuel Filter Location | Fuel strainer attaches to lower end of fuel sender. | ||
| Fuel Filter R & I | FUEL TANK MODULE REPLACEMENT | ||
| Ignition | |||
| Firing Order & Cylinder Identification | |||
| 2.4L | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| 3.5L & 3.9L | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | 2.4L Coil on plug 3.5L & 3.9L 4,018 ohms per meter (1,225 ohms per ft) |
||
| Ignition Wires (Routing) | 2.4L Coil on plug 3.5L See illustrations under SPARK PLUG WIRE REPLACEMENT 3.9L See illustrations under SPARK PLUG WIRE REPLACEMENT |
||
| Spark Plug | |||
| 2.4L | |||
| Type | GM P/N 12569190 or AC 41-981 | ||
| Gap | 0.042 In. (1.06 mm) | ||
| Torque | 15 Ft. Lbs. (20 N.m) | ||
| 3.5L | |||
| Type | NA | ||
| Gap | 0.060 In. (1.52 mm) | ||
| Torque | New Cylinder Head - 15 Ft. Lbs. (20 N.m) Used Cylinder Head - 11 Ft. Lbs. (15 N.m) |
||
| 3.9L | |||
| Type | GM P/N 12591131 or AC Delco #41-100 | ||
| Gap | 0.040 In. (1.02 mm) | ||
| Torque | 11 Ft. Lbs. (15 N.m) | ||
| Starting | |||
| Starter | STARTING SYSTEM DESCRIPTION AND OPERATION | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 100 Ft. Lbs. (140 N.m) | ||