Torque Specifications
FASTENER TIGHTENING SPECIFICATIONS
| Application | Specification | ||
|---|---|---|---|
| Metric | English | ||
| A/C Compressor to Block Bolt | 20 N.m | 15 lb ft | |
| Balance Shaft Adjustable Chain Guide Bolt | 10 N.m | 89 lb in | |
| Balance Shaft Bearing Carrier to Block Bolt | 10 N.m | 89 lb in | |
| Balance Shaft Fixed Chain Guide Bolt | 10 N.m | 89 lb in | |
| Balance Shaft Sprocket Bolt | 50 N.m | 37 lb ft | |
| Cam Cover to Cylinder Head Bolt | 10 N.m | 89 lb in | |
| Cam Cover to Ground Cable Bolt | 10 N.m | 89 lb in | |
| Cam Cover to Ground Cable Stud | 10 N.m | 89 lb in | |
| Camshaft Bearing Cap Bolt | 10 N.m | 89 lb in | |
| Camshaft Sprocket Bolt | |||
| First Pass | 85 N.m | 63 lb ft | |
| Final Pass | 30 degrees | ||
| Camshaft Timing Chain Tensioner | 75 N.m | 55 lb ft | |
| Chain Guide Plug | 90 N.m | 59 lb ft | |
| Crankshaft Pulley Bolt | |||
| First Pass | 100 N.m | 74 lb ft | |
| Final Pass | 75 degrees | ||
| Crankshaft Position Sensor Bolt | 10 N.m | 89 lb in | |
| Cylinder Head Bolt | |||
| First Pass | 30 N.m | 22 lb ft | |
| Final Pass | 155 degrees | ||
| Cylinder Head Front Chaincase Bolt | 35 N.m | 26 lb ft | |
| Cylinder Head Oil Gallery Plug | 35 N.m | 26 lb ft | |
| Dipstick Guide to Intake Manifold Bolt | 10 N.m | 89 lb in | |
| Drive Belt Tensioner Bolt | 45 N.m | 33 lb ft | |
| EGR Cover Bolt | 25 N.m | 18 lb ft | |
| Elek. ICM Cover Bolt | 10 N.m | 89 lb in | |
| Engine Coolant Temperature Sensor | 22 N.m | 16 lb ft | |
| Engine Lift Bracket Front Bolt | 25 N.m | 18 lb ft | |
| Engine Lift Bracket Rear Bolt | 25 N.m | 18 lb ft | |
| Exhaust Manifold to Cylinder Head Nut | 12 N.m | 9 lb ft | |
| Exhaust Manifold to Cylinder Head Stud | 10 N.m | 89 lb in | |
| Exhaust Manifold Pipe Flange Stud | 16 N.m | 12 lb ft | |
| Flexplate (AMT) Bolt | |||
| First Pass | 53 N.m | 39 lb ft | |
| Final Pass | 25 degrees | ||
| Flywheel (SMT) Bolt | |||
| First Pass | 53 N.m | 39 lb ft | |
| Final Pass | 25 degrees | ||
| Front Cover to Block Bolt | 25 N.m | 18 lb ft | |
| Front Lift Bracket Bolt | 25 N.m | 18 lb ft | |
| Fuel Pipe Bracket Bolt | 10 N.m | 89 lb in | |
| Fuel Rail Bracket Stud | 10 N.m | 89 lb in | |
| Generator to Block Bolt | 20 N.m | 15 lb ft | |
| Heat Shield to Exhaust Manifold Bolt | 23 N.m | 17 lb ft | |
| Ignition Coil Bolt | 10 N.m | 89 lb In | |
| Intake Camshaft Rear Cap Bolt | 25 N.m | 18 lb ft | |
| Intake Manifold to Cylinder Head Bolt | 10 N.m | 89 lb in | |
| Intake Manifold to Cylinder Head Nut | 10 N.m | 89 lb in | |
| Intake Manifold to Cylinder Head Stud | 6 N.m | 53 lb In | |
| Knock Sensor Bolt | 25 N.m | 18 lb ft | |
| Oil Filter Housing Cover | 25 N.m | 18 lb ft | |
| Oil Pan Drain Plug | 25 N.m | 18 lb ft | |
| Oil Pan to Block Bolts | 25 N.m | 18 lb ft | |
| Oil Pressure Switch | 22 N.m | 16 lb ft | |
| Oil Pump Cover Bolt | 6 N.m | 53 lb in | |
| Oil Pump Pressure Relief Valve Plug | 40 N.m | 30 lb ft | |
| Oxygen Sensor | 42 N.m | 31 lb ft | |
| Power Steering Pump Bolt | 25 N.m | 18 lb ft | |
| Rear Lift Bracket Bolt | 25 N.m | 18 lb ft | |
| Spark plug | 20 N.m | 15 lb ft | |
| Starter Motor to Block Bolt | 40 N.m | 30 lb ft | |
| Thermostat Housing to Block Bolts | 10 N.m | 89 lb in | |
| Throttle Body Bolt | 10 N.m | 89 lb in | |
| Throttle Body Nut | 10 N.m | 89 lb in | |
| Throttle Body Stud | 6 N.m | 53 lb in | |
| Timing Adjustable Chain Guide Bolt | 10 N.m | 89 lb in | |
| Timing Chain Oil Nozzle Bolt | 10 N.m | 89 lb in | |
| Timing Fixed Chain Guide Bolt | 10 N.m | 89 lb in | |
| Timing Upper Chain Guide Bolt | 10 N.m | 89 lb In | |
| Vent Tube to Cylinder Head | 15 N.m | 11 lb ft | |
| Water Jacket Drain Plug | 20 N.m | 15 lb ft | |
| Water Pipe Support Bracket Bolt | 10 N.m | 89 lb in | |
| Water Pump Access Cover Bolt | 7 N.m | 62 lb In | |
| Water Pump/Balance Shaft Chain Tensioner Bolt | 10 N.m | 89 lb in | |
| Water Pump Bolts | 25 N.m | 18 lb ft | |
| Water Pump Sprocket Bolt | 10 N.m | 89 lb In | |