LEMON Manuals: Even more car manuals for everyone
Home >> Plymouth >> 1998 >> Voyager Base, 2.4 B >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 2 (3.0L V6 Engine) >> Torque Specifications

Torque Specifications

WARNING: This page is about a different variant/trim than selected.
TORQUE SPECIFICATIONS

Application Ft. Lbs. (N.m)
Camshaft Bearing Cap Bolt (1)
Camshaft Sprocket Bolt 70 (95)
Connecting Rod Cap Bolt (2) 20 (27)
Connecting Rod Nut 38 (52)
Crankshaft Main Bearing Cap/Bedplate Bolt
8-mm (3)
11-mm (2) 30 (41)
Crankshaft Pulley Bolt 100 (135)
Cylinder Head Bolt (4) 80 (109)
Distributor Drive Adapter Bolt 10 (13.6)
Engine Bracket-To-Cylinder Block Bolt 35 (47)
Exhaust Crossover Pipe Bolt 51 (69)
Exhaust Manifold Nut 16 (22)
Flexplate-To-Crankshaft Bolt 70 (95)
Front Engine Mount-To-Cylinder Block Bolt/Nut (Bolts 2, 3 & 4) (5) 75 (102)
Front Engine Mount-To-Frame Rail Bolt/Nut (Bolts 1 & 5) (5) 40 (54)
Front Engine Mount-To-Transmission 40 (54)
Intake Manifold Bolt (6) 20 (28)
Left (Flexplate Side) Engine Mount Through-Bolt 55 (75)
Left (Flexplate Side) Engine Mount-To-Frame Rail Bolt 50 (68)
Left Engine Mount-To-Transmission Bolt 40 (55)
Main Bearing Cap Assembly Bolt (7) 61 (83)
Oil Pan Drain Plug 29 (39)
Oil Pump Relief Plunger Plug 36 (49)
Oil Pump-To-Block Bolt 11 (15)
Pick-Up Tube Bolt 20 (28)
Rear Engine Mount-To-Crossmember Bolt 45 (61)
Right (Timing Belt Side) Engine Mount-To-Frame Rail Bolt 50 (68)
Right (Timing Belt Side) Engine Mount Through-Bolt 111 (150)
Right (Timing Belt Side) Engine Mount Vertical Bolt/Nut 75 (102)
Timing Belt Tensioner Bolt 20 (28)
Torque Converter-To-Flexplate Bolt 55 (75)
Transaxle-To-Cylinder Block Bolt 75 (102)
Upper Air Intake Bolt (8) 11 (15.0)
Vibration Damper Bolt 100 (135)
INCH Lbs. (N.m) 
Crankshaft Rear Oil Seal Retainer Bolt 104 (11.7)
Cylinder Head Cover Screws 88 (10)
Exhaust Manifold-To-Cylinder Head Bolt 191 (22)
Exhaust Manifold Heat Shield Bolt 106 (12)
Fuel Pressure Regulator Bolt/Nut 95 (10.7)
Fuel Rail Bolt 115 (13.0)
Oil Pan Bolt (9) 105 (12)
Oil Pump Cover Screw 104 (9)
Radiator Mounting Screws 105 (12)
Timing Belt Cover Bolt 115 (13.0)
Valve Cover Bolt 105 (12)
Water Pump Bolt 240 (27)
(1) Tighten camshaft bearing cap bolts to 85 INCH lbs. (9.6 N.m) in the following sequence: No. 3, No. 2, No. 1 and then No. 4. camshaft bearing cap. Repeat procedure and tighten bolts to 15 ft. lbs. (20 N.m).
(2) Tighten additional 1/4 turn.
(3) Tighten 8mm crankshaft main bearing bolts to 21 ft. lbs. (34 N.m).
(4) With cylinder head cold, tighten cylinder head bolts to specification in sequence, using 3 steps. See Figure.
(5) See Figure.
(6) Tighten bolts to specification in sequence. See Figure.
(7) Coat bolts with oil before installing. Tighten bolts in to specification in sequence. See Figure.
(8) Tighten bolts to specification in sequence. See Figure.
(9) Tighten bolts to specification in sequence. See Figure.