Removal & Installation
WARNING: This page is about the Custom Cruiser 5.7L Eng VIN N, which is a different variant/trim than selected.
TRANS ID - 200, 200C, 200-4R
| Applies To | Note | Standard Hours | Warranty Hours | Skill Level |
|---|
| | 2.4 | | C |
| Combination Procedure: CONVERTER: Drain & Test: |
| | 0.2 | 0.2 | C |
| Combination Procedure: CONVERTER BUSHING & SEAL: Remove & Replace: |
| | 0.3 | 0.2 | B |
| Combination Procedure: CONVERTER SEAL: Remove & Replace: |
| | 0.2 | 0.1 | B |
| Combination Procedure: FLYWHEEL: Remove & Replace: |
| | 0.2 | 0.2 | C |
| Combination Procedure: FRONT PUMP: Overhaul Removed: |
| | 0.5 | 0.5 | B |
| Combination Procedure: FRONT PUMP: Remove & Replace: |
| | 0.6 | 0.6 | B |
| Combination Procedure: TORQUE CONVERTER: Remove & Replace: |
| | 0.1 | | C |
| Combination Procedure: TRANSMISSION ASSEMBLY: Replace: |
| | 0.6 | 0.3 | C |
| Combination Procedure: TRANSMISSION CASE: Remove & Replace: |
| | 3.2 | 2.4 | A |
TRANS ID - 250, 250C, 350, 350C
| Applies To | Note | Standard Hours | Warranty Hours | Skill Level |
|---|
| | 2.8 | | C |
| Combination Procedure: CONVERTER: Drain & Test: |
| | 0.2 | | C |
| Combination Procedure: EXTENSION HOUSING: Remove & Replace: |
| | 0.2 | | B |
| Combination Procedure: FLYWHEEL: Remove & Replace: |
| | 0.3 | | C |
| Combination Procedure: FRONT PUMP: Overhaul Removed: |
| | 0.5 | | B |
| Combination Procedure: FRONT PUMP: Remove & Replace: |
| | 0.5 | | B |
| Combination Procedure: FRONT PUMP BUSHING & SEAL: Remove & Replace: |
| | 0.3 | | B |
| Combination Procedure: FRONT PUMP SEAL: Remove & Replace: |
| | 0.1 | | B |
| Combination Procedure: INTERMEDIATE CLUTCH ACCUMULATOR: Remove & Replace or Overhaul: |
| | 0.2 | | A |
| Combination Procedure: TORQUE CONVERTER: Remove & Replace: |
| | 0.1 | | C |
| Combination Procedure: TRANSMISSION ASSEMBLY: Replace: |
| | 0.6 | 0.3 | C |
TRANS ID - 375, 400, 425
| Applies To | Note | Standard Hours | Warranty Hours | Skill Level |
|---|
| | 2.8 | 2.1 | C |
| Combination Procedure: BAND: Remove & Replace: |
| Front | | 1.0 | | A |
| Rear or Both | | 1.7 | | A |
| Combination Procedure: CARRIER PINIONS: Remove & Replace: |
| Both | | 2.9 | | B |
| Output | | 2.4 | | B |
| Reaction | | 2.2 | | B |
| Combination Procedure: CLUTCH PLATES: Remove & Replace: |
| Direct | | 1.1 | | A |
| Forward | | 1.1 | | A |
| Forward and Direct | | 1.5 | | A |
| Intermediate | | 1.1 | | A |
| Intermediate and Direct | | 1.5 | | A |
| Combination Procedure: CONVERTER: Drain & Test: |
| | 0.2 | | C |
| Combination Procedure: CONVERTER BUSHING & SEAL: Remove & Replace: |
| | 0.3 | | B |
| Combination Procedure: CONVERTER SEAL: Remove & Replace: |
| | 0.2 | | B |
| Combination Procedure: FLYWHEEL: Remove & Replace: |
| | 0.3 | | C |
| Combination Procedure: FRONT PUMP: Overhaul Removed: |
| | 0.5 | | B |
| Combination Procedure: FRONT PUMP: Remove & Replace: |
| | 0.4 | | B |
| Combination Procedure: INTERMEDIATE SPRAG: Overhaul: |
| | 1.6 | | A |
| Combination Procedure: LOW SPRAG: Remove, Install, and Overhaul: |
| | 2.5 | | A |
| Combination Procedure: TORQUE CONVERTER: Remove & Replace: |
| | 0.1 | | C |
| Combination Procedure: TRANSMISSION ASSEMBLY: Replace: |
| | 0.6 | | C |
| Combination Procedure: TRANSMISSION CASE: Remove & Replace: |
| | 2.5 | | A |