LEMON Manuals: Even more car manuals for everyone
Home >> Nissan-Datsun >> 2020 >> Kicks S >> Repair and Diagnosis >> Transmission >> Automatic Trans >> Automatic Transmission >> System Description >> Diagnosis System (TCM) >> CONSULT Function >> Data Monitor

Data Monitor

NOTE: The following table includes information (items) inapplicable to this vehicle. For information (items) applicable to this vehicle, refer to CONSULT display items.

x: Application SYMBOL : Optional selection

Monitored item

(Unit)

Remarks

VSP SENSOR

(km/h or mph)

Displays the vehicle speed calculated from the CVT output shaft speed.

ESTM VSP SIG

(km/h or mph)
  • Displays the vehicle speed signal (ABS) received through CAN communication.
  • Models with ABS are displayed.

PRI SPEED SEN

(RPM)

Displays the primary pulley speed calculated from the pulse signal of the primary speed sensor.

SEC REV SENSOR

(RPM)

Displays the secondary pulley speed calculated from the pulse signal of the secondary speed sensor.

VHCL/S SE (REV)

(RPM)

Displays the CVT output shaft speed calculated from the pulse signal of the output speed sensor.

ENG SPEED SIG

(RPM)

Displays the engine speed received through CAN communication.

LINE PRESSURE SEN

(V)

Displays the signal voltage of the line pressure sensor.

ATF TEMP SEN

(V)

Displays the signal voltage of the CVT fluid temperature sensor.

G SENSOR

(V)

Displays the signal voltage of the G sensor.

VIGN SEN

(V)

Displays the battery voltage applied to TCM.

VEHICLE SPEED

(km/h or mph)

Displays the vehicle speed recognized by TCM.

INPUT REV

(RPM)

Displays the input shaft speed of CVT recognized by TCM.

PRI SPEED

(RPM)

Displays the primary pulley speed recognized by TCM.

SEC SPEED

(RPM)

Displays the secondary pulley speed recognized by TCM.

OUTPUT REV

(RPM)

Displays the output shaft speed of CVT recognized by TCM.

ENG SPEED

(RPM)

Displays the engine speed recognized by TCM.

SLIP REV

(RPM)

Displays the speed difference between the input shaft speed of CVT and the engine speed.

TOTAL GEAR RATIO

Displays the total CVT gear ratio calculated from input shaft speed/output shaft speed of CVT.

PULLEY GEAR RATIO

Displays the pulley gear ratio calculated from primary pulley speed/secondary pulley speed.

AUX GEARBOX

Displays the gear position of the auxiliary gearbox recognized by TCM.

G SPEED

(G)

Displays the acceleration and deceleration speed of the vehicle calculated from vehicle speed change.

ACCEL POSI SEN 1

(deg)

Displays the estimated throttle position received through CAN communication.

ENG TRQ ACT

(Nm)

Display the estimated engine torque recognized by TCM.

ENG TRQ PTD

(Nm)

Display the required engine torque recognized by TCM.

VENG TRQ

(Nm)

Display the engine torque recognized by TCM.

PRI TRQ

(Nm)

Display the input shaft torque of CVT.

TRQ RTO

Display the torque ratio of torque converter.

SEC PRESSURE

(MPa, kg/cm2 or psi)

Displays the secondary pressure calculated from the signal voltage of the secondary pressure sensor.

PRI PRESSURE

(MPa, kg/cm2 or psi)

Displays the primary pressure calculated from the signal voltage of the primary pressure sensor.

LINE PRESSURE

(MPa, kg/cm2, or psi)

Displays the secondary pressure (line pressure) calculated from the signal voltage of the secondary pressure sensor.

FLUID TEMP

(deg.C or deg.F)

Displays the CVT fluid temperature calculated from the signal voltage of the CVT fluid temperature sensor.

DSR REV

(RPM)

Displays the target primary pulley speed calculated from processing of gear shift control.

TRGT GEAR RATIO

Displays the target gear ratio from the input shaft to the output shaft of CVT calculated from processing of gear shift control.

TGT PLLY GR RATIO

Displays the target gear ratio of the pulley from processing of gear shift control.

TRGT AUX GEARBOX

Displays the target gear of the auxiliary gearbox calculated from processing of gear shift control.

LU PRS

(MPa, kg/cm2, or psi)

Displays the target oil pressure of the torque converter clutch solenoid valve calculated from oil pressure processing of gear shift control.

LINE PRS

(MPa, kg/cm2, or psi)

Displays the target oil pressure of the line pressure solenoid valve calculated from oil pressure processing of gear shift control.

TRGT PRI PRESSURE

(MPa, kg/cm2, or psi)

Displays the target oil pressure of the primary pressure solenoid valve calculated from oil pressure processing of gear shift control.

TARGET SEC PRESSUR

(MPa, kg/cm2 or psi)

Displays the target oil pressure of the secondary pressure solenoid valve calculated from oil pressure processing of gear shift control.

TRGT HC/RB PRESS

(MPa, kg/cm2, or psi)

Displays the target oil pressure of the high clutch & reverse brake solenoid valve calculated from oil pressure processing of gear shift control.

TRGT LB PRESSURE

(MPa, kg/cm2, or psi)

Displays the target oil pressure of the low brake solenoid valve calculated from oil pressure processing of gear shift control.

ISOLT1

(A)

Displays the command current from TCM to the torque converter clutch solenoid valve.

ISOLT2

(A)

Displays the command current from TCM to the line pressure solenoid valve.

PRI SOLENOID

(A)

Displays the command current from TCM to the primary pressure solenoid valve.

SEC SOLENOID CURRENT

(A)

Displays the command current from TCM to the secondary pressure solenoid valve.

HC/RB SOLENOID

(A)

Displays the command current from TCM to the high clutch& reverse brake solenoid valve.

L/B SOLENOID

(A)

Displays the command current from TCM to the low brake solenoid valve.

SOLMON1

(A)

Monitors the command current from TCM to the torque converter clutch solenoid valve and displays the monitored value.

SOLMON2

(A)

Monitors the command current from TCM to the line pressure solenoid valve and displays the monitored value.

PRI SOL MON

(A)

Monitors the command current from TCM to the primary pressure solenoid valve and displays the monitored value.

SEC SOL MON CURRENT

(A)

Monitors the command current from TCM to the secondary pressure solenoid valve and displays the monitored value.

HC/RB SOL MON

(A)

Monitors the command current from TCM to the high clutch& reverse brake solenoid valve and displays the monitored value.

L/B SOL MON

(A)

Monitors the current command from TCM to the low brake solenoid valve and displays the monitored value.

SEC PRESSURE SEN

(V)

Displays the signal voltage of the secondary pressure sensor.

PRI PRESSURE SEN

(V)

Displays the signal voltage of the primary pressure sensor.

D POSITION SW

(On/Off)

Displays the operation status of the transmission range switch (D position).

N POSITION SW

(On/Off)

Displays the operation status of the transmission range switch (N position).

R POSITION SW

(On/Off)

Displays the operation status of the transmission range switch (R position).

P POSITION SW

(On/Off)

Displays the operation status of the transmission range switch (P position).

BRAKESW

(On/Off)

Displays the reception status of the stop lamp switch signal received through CAN communication.

L POSITION SW

(On/Off)

Displays the operation status of the transmission range switch (L position).

IDLE SW

(On/Off)

Displays the reception status of the closed throttle position signal received through CAN communication.

SPORT MODE SW

(On/Off)

Displays the reception status of the DS (DRIVE SPORT) mode switch signal received through CAN communication.

STRDWNSW

(On/Off)

Displays the operation status of the paddle shifter (down switch).

STRUPSW

(On/Off)

Displays the operation status of the paddle shifter (up switch).

DOWNLVR

(On/Off)

Displays the operation status of the selector lever (down switch).

UPLVR

(On/Off)

Displays the operation status of the selector lever (up switch).

NONMMODE

(On/Off)

Displays if the selector lever position is not at the manual shift gate.

MMODE

(On/Off)

Displays if the selector lever position is at the manual shift gate.

SHIFT IND SIGNAL

Displays the transaxle value of shift position signal transmitted via CAN communication.

ECO MODE SIGNAL

(On/Off)

Displays the reception status of the ECO mode switch signal received through CAN communication.

CVT LAMP

(On/Off)
  • Displays the transmission status of the CVT warning lamp signal transmitted through CAN communication.
  • This monitor item does not use.

SPORT MODE IND

(On/Off)
  • Displays the transmission status of the DRIVE SPORT indicator signal transmitted through CAN communication.
  • This monitor item does not use.

MANU MODE SIGNAL

(On/Off)

Displays the transaxle status of the manual mode signal transmitted through CAN communication.

VDC ON

(On/Off)

Displays the reception status of the VDC operation signal received through CAN communication.

TCS ON

(On/Off)

Displays the reception status of the TCS operation signal received through CAN communication.

ABS FAIL SIGNAL

(On/Off)

Displays the reception status of the ABS malfunction signal received through CAN communication.

ABS ON

(On/Off)

Displays the reception status of the ABS operation signal received through CAN communication.

AIR BLDING STATE

(INCOMP)
  • Displays the status of "ELECTRIC O.P. AIR BLEEDING" in "Work Support".
  • This monitor item does not use.

DRIVE MODE STATS

Displays the drive mode status recognized by TCM.

4WD FAIL SIGNAL

(On/Off)

Displays the reception status of the 4WD malfunction signal received through CAN communication.

4WD OPERATION SIG

(On/Off)

Displays the reception status of the 4WD operation signal received through CAN communication.

4WD-TCS SIGNAL

(On/Off)

Displays the reception status of the engine torque down request signal received through CAN communication.

RANGE

Displays the gear position recognized by TCM.

M GEAR POS

Display the target gear of manual mode

G SEN SLOPE

(%)

Displays the gradient angle calculated from the G sensor signal voltage.

ENGBRKLVL

(On/Off)

Displays the setting of "ENGINE BRAKE ADJ." in "Work Support".

SNOW MODE

(On/Off)

Displays whether it is the SNOW mode.

ECO MODE

(On/Off)

Displays whether it is the ECO mode.

NORMAL MODE

(On/Off)

Displays whether it is the NORMAL mode.

SPORT MODE

(Off)
  • Displays whether it is the DS (DRIVE SPORT) mode.
  • This monitor item does not use.

PVIGN VOLT

(V)

Displays the backup voltage of TCM.

TRGT AUX GR RATIO

Displays the target gear ratio of the auxiliary gearbox calculated from processing of gear shift control.

ELECTRIC OP DUTY

(%)

Displays the command signal value (duty) of the electric oil pump transmitted from TCM.

E-OP DUTY MON

(%)

Monitors the status signal value (duty) transmitted from the electric oil pump and displays the monitored value.

ELECTRIC OP RELAY

(On/Off)
  • Displays the command status from TCM to the electric oil pump relay.
  • This monitor item does not use.

E-OP RELAY MON

(On/Off)
  • Monitors the command status from TCM to the oil pump relay and displays the monitored value.
  • This monitor item does not use.

G SEN CALIBRATION

(YET/DONE)

Displays the status of "G SENSOR CALIBRATION" in "Work support".

CVT-B
  • Displays CVT fluid temperature count.
  • This monitor item does not use.

CVT-A
  • Displays CVT fluid temperature count.
  • This monitor item does not use.

Low brake pressure

(MPa, kg/cm2, or psi)

Displays the low brake pressure calculated from the signal voltage of the low brake pressure sensor.

Reverse brake pressure

(MPa, kg/cm2, or psi)
  • Displays the reverse brake pressure calculated from the signal voltage of the reverse brake pressure sensor.
  • This monitor item does not use.

High clutch pressure

(MPa, kg/cm2, or psi)

Displays the high clutch pressure calculated from the signal voltage of the high clutch pressure sensor.

Low brake press correction vlu

(MPa, kg/cm2, or psi)

Displays the low brake pressure correction value calculated from oil pressure processing of gear shift control.

Low brake pressure start value

(MPa, kg/cm2, or psi)

Displays the low brake pressure start value calculated from oil pressure processing of gear shift control.

Target line pressure

(MPa, kg/cm2, or psi)

Displays the target oil pressure of the line pressure solenoid valve calculated from oil pressure processing of gear shift control.

Low brake pressure sensor sig

(V)

Displays the signal voltage of the low brake pressure sensor.

Reverse brake press sen sig

(V)
  • Displays the signal voltage of the reverse brake pressure sensor.
  • This monitor item does not use.

High clutch press sensor sig

(V)

Displays the signal voltage of the high clutch pressure sensor.
scientia non olet · About LEMON Manuals