LEMON Manuals: Even more car manuals for everyone
Home >> Nissan-Datsun >> 2019 >> Maxima SL >> Repair and Diagnosis >> Transmission >> Automatic Trans >> Automatic Transmission (Introduction And Basic Inspection) >> System Description >> Diagnosis System (TCM) >> Counter System >> Driving Condition

Driving Condition

Driving condition A 

Driving condition A is the driving condition that provides warm-up.

In specific, count-up is performed when all of the following conditions are satisfied.

NOTE:
  • If the same malfunction is detected regardless of the driving condition, reset the A counter.
  • When the above is satisfied without detecting the same malfunction after turning off MIL, count up the A counter.
  • When MIL goes off due to the malfunction and the A counter reaches 40, the DTC is erased.

Driving condition B 

Driving condition B is different by each DTC.

In specific, count-up is performed when the following conditions are satisfied.

DTC

Driving condition

P062F, P0740, P0743, P0778, P0779, P0863, P0890, P0962, P0963, P0966, P0967

Start the engine and let it idle for least 1 second.

U0073, U0100, U0140, U0141, U0155, U0300, U1000, U1117

Start the engine and let it idle for least 2 seconds.

P0711
  1. Turn ignition switch OFF and leave the vehicle for 12 hours.
  2. Start the engine.
    NOTE: When starting the engine, CVT fluid temperature is less than 20 deg. C (68 deg. F).
  3. Drive the vehicle for the total minutes specified in the Driving time column below with the following conditions satisfied.
    • Ignition voltage: 11 V or more
    • Selector lever : "D" position
    • Throttle position : 1% or more
    • Engine speed: 450 RPM
    • Vehicle speed : 10 km/h (7 MPH) or more
    CVT Fluid Temperature/Driving Time

    CVT fluid temperature before engine start

    Driving time

    -40 deg. C (-40 deg. F) - 31 deg. C (-23.8 deg. F)

    20 minutes or more

    -30 deg. C (-22 deg. F) - 21 deg. C (-5.8 deg. F)

    18 minutes or more

    -20 deg. C (-4 deg. F) --11 deg. C (-12.2 deg. F)

    14 minutes or more

    -10 deg. C (14 deg. F) - 1 deg. C (30.2 deg. F)

    10 minutes or more

    0 deg. C (32 deg. F) - 9 deg. C (48.2 deg. F)

    7 minutes or more
  4. CVT fluid temperature rises to 20 deg. C (68 deg. F) or more.

P0712

Start the engine and let it idle for least 5 seconds.

P0705
  1. Turn ignition switch ON.
  2. Shift the selector lever through entire positions from "P" to "D". (Hold the selector lever at each position for 2 seconds or more.)

P0706
  1. Turn ignition switch ON.
  2. Shift the selector lever through entire positions from "P" to "D". (Hold the selector lever at each position for 30 seconds or more.)

P0713

Drive the vehicle for 5 seconds or more under the following conditions.

  • Vehicle speed: 20 km/h (12 MPH) or more

P0715, P0716, P0717, P0791, P0792, P0793

Drive the vehicle for 5 seconds or more under the following conditions.

  • Selector lever : "D" position
  • Engine speed : 1, 200 RPM or more
  • Vehicle speed : 40 km/h (25 MPH) or more

P0744

Drive the vehicle for 10 seconds or more under the following conditions.

  • Selector lever : "D" position
  • CVT fluid temperature: 20 deg. C (68 deg. F) or more
  • Vehicle speed : 40 km/h (25 MPH) or more

P0746

Drive the vehicle for 5 seconds or more under the following conditions.

  • Selector lever : "D" position
  • Accelerator pedal position : 0.5/8 or more
  • Vehicle speed : 40 km/h (25 MPH) or more

P0776

Drive the vehicle for 10 seconds or more under the following conditions.

  • Selector lever : "D" position
  • Accelerator pedal position : 1.0/8 or more
  • Vehicle speed : 40 km/h (25 MPH) or more

P0841

Drive the vehicle for 5 seconds or more under the following conditions.

  • Selector lever : "D" position
  • Vehicle speed : 40 km/h (25 MPH) or more

P0847, P0848, P084C, P084D

Start the engine and wait for at least 10 seconds.

CAUTION: When the ambient temperature is less than -20 deg. C (-4 deg. F) and the engine is cold, warm up the engine for approximately 5 minutes.

P0965

Drive the vehicle for 10 seconds or more under the following conditions.

  • Vehicle speed : 40 km/h (25 MPH) or more

P2765, P2766, P2767

Drive the vehicle for 5 seconds or more under the following conditions.

  • Selector lever : "D" position
  • Engine speed : 1, 200 RPM or more
  • Vehicle speed : 55 km/h (34 MPH) or more

P2813
  1. Start the engine.
  2. Repeat D position creep start and a stop more than five times.
  3. Drive the vehicle for 30 seconds or more in total under the following conditions.
    • Selector lever : "D" position
    • Accelerator pedal position : 0.7/8 or more
    • Vehicle speed : 40 km/h (25 MPH) or more

P2814, P2815
  1. Start the engine.
  2. Shift the selector lever from N position to D and keep 5 seconds or more.
  3. Shift the selector lever from N position to R and keep 5 seconds or more.
  4. Shift the selector lever from P position to R and keep 5 seconds or more.
NOTE:
  • If the same malfunction is detected regardless of the driving condition, reset the B counter.
  • When the above is satisfied without detecting the same malfunction, count up the B counter.
  • When the B counter reaches 3 without malfunction, MIL goes off.
  • When the B counter is counted once without detecting the same malfunction after TCM memorizes DTC of the 1st trip, DTC of the 1st trip is erased.
scientia non olet · About LEMON Manuals