Work Procedure

CAUTION:

Use "Manual Configuration" only when "TYPE ID" of the chassis control module (with built in steering angle sensor) cannot be read.
After configuration, turn the ignition switch from OFF to ON and check that the chassis control warning to information display of combination meter displays OFF after staying illuminated for approximately two seconds.
If an error occurs during configuration, start over from the beginning.

CHECKING TYPE ID (1)
Use FAST (service parts catalogue) to search the chassis control module (with built in steering angle sensor) of the applicable vehicle and find "Type ID".

Is "Type ID" displayed?

YES

Print out "Type ID" and GO TO 2.

NO

"Configuration" is not required for the chassis control module (with built in steering angle sensor). Replace in the usual manner. Refer to CHASSIS CONTROL MODULE (WITH BUILT IN STEERING ANGLE SENSOR) : Removal & Installation .
CHECKING TYPE ID (2)
CONSULT Configuration
1. Select "Before Replace ECU" of "Read/Write Configuration".
2. Check that "Type ID" is displayed on the CONSULT screen.
Is "Type ID" displayed?

YES

GO TO 3.

NO

GO TO 7.
VERIFYING TYPE ID (1)
CONSULT Configuration

Compare a "Type ID" displayed on the CONSULT screen with the one searched for using FAST (service parts catalogue) to check that these "Type ID" agree with each other.

NOTE: For the "Type ID" searched for using FAST (service parts catalog), use the last five digits of the "Type ID".

GO TO 4.
SAVING TYPE ID
CONSULT Configuration

Save "Type ID" on CONSULT.

GO TO 5.
REPLACING CHASSIS CONTROL MODULE (WITH BUILT IN STEERING ANGLE SENSOR) (1)
Replace the chassis control module (with built in steering angle sensor). Refer to CHASSIS CONTROL MODULE (WITH BUILT IN STEERING ANGLE SENSOR) : Removal & Installation .

GO TO 6.
WRITING (AUTOMATIC WRITING)
CONSULT Configuration
1. Select "After Replace ECU" of "Re/programming, Configuration" or that of "Read / Write Configuration".
2. Select the "Type ID" agreeing with the one stored on CONSULT and the one searched by using FAST (service parts catalogue) to write the "Type ID" into the chassis control module (with built in steering angle sensor).
  NOTE: For the "Type ID" searched for using FAST (service parts catalog), use the last five digits of the "Type ID".
GO TO 9.
REPLACING CHASSIS CONTROL MODULE (WITH BUILT IN STEERING ANGLE SENSOR) (2)
Replace the chassis control module (with built in steering angle sensor). Replace in the usual manner. Refer to CHASSIS CONTROL MODULE (WITH BUILT IN STEERING ANGLE SENSOR) : Removal & Installation .

GO TO 8.
WRITING (MANUAL WRITING)
CONSULT Configuration
1. Select "Manual Configuration".
2. Select the "Type ID" searched by using FAST (service parts catalogue) to write the "Type ID" into the chassis control module (with built in steering angle sensor).
  NOTE: For the "Type ID" searched for using FAST (service parts catalog), use the last five digits of the "Type ID".
GO TO 9.
VERIFYING TYPE ID (2)
Compare "Type ID" written into the chassis control module (with built in steering angle sensor) with the one searched by using FAST (service parts catalogue) to check that these "Type ID" agree with each other.

NOTE: For the "Type ID" searched for using FAST (service parts catalog), use the last five digits of the "Type ID".

GO TO 10.
PERFORM ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION
Perform adjustment of steering angle sensor neutral position. Refer to Work Procedure .

NO

GO TO 11.
CHECKING CHASSIS CONTROL WARNING
1. Turn the ignition switch OFF.
2. Turn the ignition switch ON and check that the chassis control warning to information display of combination meter displays OFF after staying illuminated for approximately two seconds.
  CAUTION: Never start the engine.
Is the display?

YES

Perform the "Self Diagnostic Result" of "CHASSIS CONTROL". Refer to DTC Index .

NO

GO TO 12.
PERFORMING SUPPLEMENTARY WORK
CONSULT Configuration
1. Perform "Self Diagnostic Result" of all systems.
2. Erase "Self Diagnostic Result".
End of work.