Data Monitor

NOTE: The following table includes information (items) inapplicable to this vehicle. For information (items) applicable to this vehicle, refer to CONSULT display items.

x: Application, O: Optional selection
Monitored item	(Unit)	Monitor item selection		Remarks
Monitored item	(Unit)	MAIN SIGNALS	ECU INPUT SIGNALS	Remarks
VSP SENSOR	(km/h or mph)	O	x	Displays the vehicle speed calculated from the CVT output shaft speed.
ESTM VSP SIG	(km/h or mph)	O	x	Displays the vehicle speed signal (ABS) received through CAN communication.
PRI SPEED SEN	(rpm)	O	x	Displays the primary pulley speed calculated from the pulse signal of the primary speed sensor.
SEC REV SENSOR	(rpm)	O	x	Displays the secondary pulley speed calculated from the pulse signal of the secondary speed sensor.
VHCL/S SE (REV)	(rpm)	O	x	Displays the CVT output shaft speed calculated from the pulse signal of the output speed sensor.
ENG SPEED SIG	(rpm)	O	x	Displays the engine speed received through CAN communication.
LINE PRESSURE SEN	(V)	O	x	Displays the signal voltage of the line pressure sensor.
ATF TEMP SEN	(V)	O	x	Displays the signal voltage of the CVT fluid temperature sensor.
G SENSOR	(V)	O	x	Displays the signal voltage of the G sensor.
VIGN SEN	(V)	O	x	Displays the battery voltage applied to TCM.
VEHICLE SPEED	(km/h or mph)	x	O	Displays the vehicle speed recognized by TCM.
INPUT REV	(rpm)	O	O	Displays the input shaft speed of CVT recognized by TCM.
PRI SPEED	(rpm)	x	O	Displays the primary pulley speed recognized by TCM.
SEC SPEED	(rpm)	O	O	Displays the secondary pulley speed recognized by TCM.
OUTPUT REV	(rpm)	O	O	Displays the output shaft speed of CVT recognized by TCM.
ENG SPEED	(rpm)	x	O	Displays the engine speed recognized by TCM.
SLIP REV	(rpm)	x	O	Displays the speed difference between the input shaft speed of CVT and the engine speed.
TOTAL GEAR RATIO		x	O	Displays the total CVT gear ratio calculated from input shaft speed/output shaft speed of CVT.
PULLEY GEAR RATIO		x	O	Displays the pulley gear ratio calculated from primary pulley speed/secondary pulley speed.
AUX GEARBOX		O	O	Displays the gear position of the auxiliary gearbox recognized by TCM.
G SPEED	(G)	O	O	Displays the acceleration and deceleration speed of the vehicle calculated from vehicle speed change.
ACCEL POSI SEN 1	(deg)	x	x	Displays the estimated throttle position received through CAN communication.
VENG TRQ	(Nm)	x	O	Display the engine torque recognized by TCM.
PRI TRQ	(Nm)	O	O	Display the input shaft torque of CVT.
TRQ RTO		O	O	Display the torque ratio of torque converter.
LINE PRESSURE	(MPa)	x	O	Displays the secondary pressure (line pressure) calculated from the signal voltage of the secondary pressure sensor.
FLUID TEMP	(°C or °F)	x	O	Displays the CVT fluid temperature calculated from the signal voltage of the CVT fluid temperature sensor.
DSR REV	(rpm)	O	O	Displays the target primary pulley speed calculated from processing of gear shift control.
TRGT GEAR RATIO		O	O	Displays the target gear ratio from the input shaft to the output shaft of CVT calculated from processing of gear shift control.
TGT PLLY GR RATIO		O	O	Displays the target gear ratio of the pulley from processing of gear shift control.
TRGT AUX GEARBOX		O	O	Displays the target gear of the auxiliary gearbox calculated from processing of gear shift control.
LU PRS	(MPa)	O	O	Displays the target oil pressure of the torque converter clutch solenoid valve calculated from oil pressure processing of gear shift control.
LINE PRS	(MPa)	O	O	Displays the target oil pressure of the line pressure solenoid valve calculated from oil pressure processing of gear shift control.
TRGT PRI PRESSURE	(MPa)	O	O	Displays the target oil pressure of the primary pressure solenoid valve calculated from oil pressure processing of gear shift control.
TRGT HC/RB PRESS	(MPa)	O	O	Displays the target oil pressure of the high clutch & reverse brake solenoid valve calculated from oil pressure processing of gear shift control.
TRGT LB PRESSURE	(MPa)	O	O	Displays the target oil pressure of the low brake solenoid valve calculated from oil pressure processing of gear shift control.
ISOLT1	(A)	x	O	Displays the command current from TCM to the torque converter clutch solenoid valve.
ISOLT2	(A)	x	O	Displays the command current from TCM to the line pressure solenoid valve.
PRI SOLENOID	(A)	x	O	Displays the command current from TCM to the primary pressure solenoid valve.
HC/RB SOLENOID	(A)	x	O	Displays the command current from TCM to the high clutch & reverse brake solenoid valve.
L/B SOLENOID	(A)	x	O	Displays the command current from TCM to the low brake solenoid valve.
SOLMON1	(A)	x	x	Monitors the command current from TCM to the torque converter clutch solenoid valve and displays the monitored value.
SOLMON2	(A)	x	x	Monitors the command current from TCM to the line pressure solenoid valve and displays the monitored value.
PRI SOL MON	(A)	x	x	Monitors the command current from TCM to the primary pressure solenoid valve and displays the monitored value.
HC/RB SOL MON	(A)	x	x	Monitors the command current from TCM to the high clutch& reverse brake solenoid valve and displays the monitored value.
L/B SOL MON	(A)	x	x	Monitors the current command from TCM to the low brake solenoid valve and displays the monitored value.
D POSITION SW	(On/Off)	O	x	Displays the operation status of the transmission range switch (D position).
N POSITION SW	(On/Off)	O	x	Displays the operation status of the transmission range switch (N position).
R POSITION SW	(On/Off)	O	x	Displays the operation status of the transmission range switch (R position).
P POSITION SW	(On/Off)	O	x	Displays the operation status of the transmission range switch (P position).
BRAKESW	(On/Off)	x	x	Displays the reception status of the stop lamp switch signal received through CAN communication.
L POSITION SW	(On/Off)	O	x	Displays the operation status of the transmission range switch (L position).
IDLE SW	(On/Off)	x	x	Displays the reception status of the closed throttle position signal received through CAN communication.
SPORT MODE SW	(On/Off)	x	x	Displays the reception status of the overdrive control switch signal received through CAN communication.
STRDWNSW	(On/Off)	O	x	Displays the operation status of the paddle shifter (down switch). It is displayed although not equipped.
STRUPSW	(On/Off)	O	x	Displays the operation status of the paddle shifter (up switch). It is displayed although not equipped.
DOWNLVR	(On/Off)	O	x	Displays the operation status of the selector lever (down switch). It is displayed although not equipped.
UPLVR	(On/Off)	O	x	Displays the operation status of the selector lever (up switch). It is displayed although not equipped.
NONMMODE	(On/Off)	O	x	Displays if the selector lever position is not at the manual shift gate. It is displayed although not equipped.
MMODE	(On/Off)	O	x	Displays if the selector lever position is at the manual shift gate. It is displayed although not equipped.
INDLRNG	(On/Off)	O	O	Displays the transmission status of the shift position (L position) signal transmitted through CAN communication.
INDDRNG	(On/Off)	O	O	Displays the transmission status of the shift position (D position) signal transmitted through CAN communication.
INGNRNG	(On/Off)	O	O	Displays the transmission status of the shift position (N position) signal transmitted through CAN communication.
INGRRNG	(On/Off)	O	O	Displays the transmission status of the shift position (R position) signal transmitted through CAN communication.
INGPRNG	(On/Off)	O	O	Displays the transmission status of the shift position (P position) signal transmitted through CAN communication.
CVT LAMP	(On/Off)	O	O	Displays the transmission status of the OD OFF indicator lamp signal transmitted through CAN communication.
SPORT MODE IND	(On/Off)	O	O	Displays the transmission status of the OD OFF indicator lamp signal transmitted through CAN communication.
MMODE IND	(On/Off)	O	O	Displays the transmission status of the manual mode signal transmitted through CAN communication. It is displayed although not equipped.
SPORT MODE SW 1	(On/Off)	O	O	Displays the reception status of the SPORT mode switch signal received through CAN communication.
VDC ON	(On/Off)	O	x	Displays the reception status of the VDC operation signal received through CAN communication.
TCS ON	(On/Off)	O	x	Displays the reception status of the TCS operation signal received through CAN communication.
ABS FAIL SIGNAL	(On/Off)	O	x	Displays the reception status of the ABS malfunction signal received through CAN communication.
ABS ON	(On/Off)	O	x	Displays the reception status of the ABS operation signal received through CAN communication.
4WD FAIL SIGNAL	(On/Off)	O	x	Displays the reception status of the 4WD malfunction signal received through CAN communication. It is displayed although not equipped.
4WD OPERATION SIG	(On/Off)	O	x	Displays the reception status of the 4WD operation signal received through CAN communication. It is displayed although not equipped.
4WD-TCS SIGNAL	(On/Off)	O	x	Displays the reception status of the engine torque down request signal received through CAN communication. It is displayed although not equipped.
RANGE		x	O	Displays the gear position recognized by TCM.
M GEAR POS		x	O	Display the target gear of manual mode It is displayed although not equipped.
G SEN SLOPE	(%)	O	O	Displays the gradient angle calculated from the G sensor signal voltage.
ENGBRKLVL	(On/Off)	O	O	Displays the setting of "ENGINE BRAKE ADJ." in "Work Support".
PVIGN VOLT	(V)	O	x	Displays the backup voltage of TCM.
TRGT AUX GR RATIO		O	O	Displays the target gear ratio of the auxiliary gearbox calculated from processing of gear shift control.
ECO SW	(On/Off)	O	O	Displays the reception status of the ECO mode switch signal received through CAN communication. Models with ECO mode are displayed.
G SEN CALIBRATION	(YET/DONE)	O	O	Displays the status of "G SENSOR CALIBRATION" in "Work support".
N IDLE STATUS	(On/Off)	O	O	Displays idle neutral status.
CVT-B		O	O	Displays CVT fluid temperature count. This monitor item does not use.
CVT-A		O	O	Displays CVT fluid temperature count. This monitor item does not use.