Terminals And Reference Values For TCM
WARNING: This page is about a different variant/trim than selected.
Data are reference values and are measured between each terminal and ground.
TERMINAL REFERENCE
| Terminal | Wire color | Item | Condition | Data (Approx.) | ||||
|---|---|---|---|---|---|---|---|---|
| 1 | GR | Line pressure solenoid valve | Release your foot from the accelerator pedal. | 5.0 - 7.0 V | ||||
| Press the accelerator pedal all the way down. | 1.0 - 3.0 V | |||||||
| 2 | LG | Secondary pressure solenoid valve | Release your foot from the accelerator pedal. | 5.0 - 7.0 V | ||||
| Press the accelerator pedal all the way down. | 3.0 - 4.0 V | |||||||
| 3 | SB | Torque converter clutch solenoid valve | When vehicle cruises in "D" position. | When CVT performs lock-up. | 6.0 V | |||
| When CVT does not perform lock-up. | 1.0 V | |||||||
| 4 | BR | Lock-up select solenoid valve | Selector lever in "P" and "N" positions | Battery voltage | ||||
| Wait at least for 5 seconds with the selector lever in "R", "D" and "L" positions | 0 V | |||||||
| 5 | L | CAN-H | - | - | ||||
| 6 | P | CAN-L | - | - | ||||
| 10 | R | Power supply | - | Battery voltage | ||||
| - | 0 V | |||||||
| 11 | L | Step motor A | Within 2 seconds after ignition switch ON, the time measurement by using the pulse width measurement function (Hi level) of CONSULT-III.*1 *1: A circuit tester cannot be used to test this item. |
30.0 msec | ||||
| 12 | Y | Step motor B | 10.0 msec | |||||
| 13 | G | ROM assembly | - | - | ||||
| 14 | Y | ROM assembly | - | - | ||||
| 15 | G | ROM assembly | - | - | ||||
| 18 | GR | P RANGE SW | Selector lever in "P" position. | Battery voltage | ||||
| Other than above position. | 0 V | |||||||
| 19 | R | Power supply | - | Battery voltage | ||||
| - | 0 V | |||||||
| 20 | W | Step motor C | Within 2 seconds after ignition switch ON, the time measurement by using the pulse width measurement function (Hi level) of CONSULT-III.*1 *1: A circuit tester cannot be used to test this item. |
30.0 msec | ||||
| 21 | P | Step motor D | 10.0 msec | |||||
| 22 | BR | R RANGE SW | Selector lever in "R" position. | Battery voltage | ||||
| Other than above position. | 0 V | |||||||
| 25 | B | Ground | Always | 0 V | ||||
| 26 | W | N RANGE SW | Selector lever in "N" position. | Battery voltage | ||||
| Other than above position. | 0 V | |||||||
| 28 | Y | Power supply (memory backup) | Always | Battery voltage | ||||
| 29 | R | Secondary speed sensor | When driving ["D" position, 20 km/h (12 MPH)]. | 570 Hz | ||||
| 30 | Y | Power supply (memory backup) | Always | Battery voltage | ||||
| 31 | LG | K-LINE | - | - | ||||
| 37 | L | Secondary pressure sensor | "N" position idle | 1.0 V | ||||
| 38 | V | Primary speed sensor | When driving ["L" position, 20 km/h (12 MPH)]. | 1250 Hz | ||||
| 41(1) | - | - | - | - | - | |||
| 42 | LG | Sensor ground | Always | 0 V | ||||
| 43 | SB | D RANGE SW | Selector lever in "D" position. | Battery voltage | ||||
| Other than above position. | 0 V | |||||||
| 44 | W | L RANGE SW | Selector lever in "" position. | Battery voltage | ||||
| Other than above position. | 0 V | |||||||
| 46 | O | Sensor power | - | 5.0 V | ||||
| - | 0 V | |||||||
| 47 | G | CVT fluid temperature sensor | When CVT fluid temperature is 20°C (68°F) | 2.0 V | ||||
| When CVT fluid temperature is 80°C (176°F) | 1.0 V | |||||||
| 48 | B | Ground | Always | 0 V | ||||
|
||||||||