LEMON Manuals: Even more car manuals for everyone
Home >> Nissan-Datsun >> 2006 >> Sentra SE-R Spec V >> Repair and Diagnosis >> Transmission >> Manual Transmission >> RS5F70A >> Preparation >> Special Service Tools

Special Service Tools

The actual shapes of the Kent-Moore tools may differ from those of the special service tools illustrated here.

SPECIAL SERVICE TOOLS

Tool number
(Kent-Moore No.)
Tool name		   Description
KV38107700
(J39027)
Preload adapter
G04192404
 Measuring turning torque of final drive assembly
Measuring total turning torque
Measuring clearance between side gear and differential case with washer
Selecting differential side bearing adjusting shim [Use with KV38106000 (J34291-B).]
KV38106000
(J34291-B)
Height gauge adapter (differential side bearing)
G04192405
 Selecting differential side bearing adjusting shim [Use with KV38107700 (J39027).]
  1. 140 mm (5.51 in) 
  2. 40 mm (1.57 in) 
  3. 16 mm (0.63 in) dia  .
  4. M8 x 1.25P 
KV32101000
(J25689-A)
Pin punch
G04133915
 Removing and installing retaining pin
Removing and installing lock pin
Removing selector shaft
Removing welch plug
  1. 4 mm (0.16 in) dia  .
KV31100300
(J25689-A)
Pin punch
G04133915
 Removing and installing retaining pin
  1. 4.5 mm (0.177 in) dia  .
ST30031000
(J22912-01)
Puller
G04192408
 Removing 3rd, 5th input gear
Removing 3rd & 4th and 5th & Rev synchronizer hub
Removing mainshaft rear bearing
Removing 2nd gear, 5th gear bush
Removing 1st & 2nd synchronizer hub, 1st and 4th main gear
Removing and installing differential side bearing
  1. 90 mm (3.54 in) dia  .
  2. 50 mm (1.97 in) dia  .
ST30021000
(J22912-01)
Puller
G04192409
 Removing input shaft front and rear bearing
Installing input shaft front and rear bearing
Installing 5th input gear, 3rd main gear and 4th main gear
Installing 1st & 2nd, 3rd & 4th and 5th & Rev synchronizer hub
Installing 2nd gear bush, 5th gear bush, Rev gear bush
Installing mainshaft rear bearing
  1. 110 mm (4.33 in) dia  .
  2. 68 mm (2.68 in) dia  .
ST33061000
(J8107-2)
Drift
G04133900
 Removing differential side bearing
  1. 39 mm (1.54 in) dia  .
  2. 29.5 mm (1.16 in) dia  .
ST33290001
(J34286)
Puller
G04192411
  • Removing idler gear bearing outer race
  1. 250 mm (9.84 in) 
  2. 160 mm (6.30 in) 
ST33230000
(J25805-01)
Drift
G04192412
 Removing differential oil seal
Installing differential side bearing
  1. 51 mm (2.01 in) dia  .
  2. 28.5 mm (1.122 in) dia  .
ST30720000
(J25405)
Drift
G04150396
 Installing differential side bearing outer race
  1. 77 mm (3.03 in) dia  .
  2. 55.5 mm (2.185 in) dia  .
ST22350000
(J25678-01)
Drift
G04192414
 Installing input shaft front and rear bearing
  1. 34 mm (1.34 in) dia  .
  2. 28 mm (1.10 in) dia  .
ST22452000
(J34335)
Drift
G04192415
 Installing 3rd and 4th main gear
Installing 5th gear bush
Installing 5th & Rev synchronizer hub
Installing Rev gear bush
Installing mainshaft rear bearing
  1. 45 mm (1.77 in) dia  .
  2. 36 mm (1.42 in) dia  .
ST37750000
(J34335)
Drift
G04192416
 Installing input shaft oil seal
Installing 5th synchronizer
Installing mainshaft rear bearing
Installing 5th main gear
Installing 3rd & 4th synchronizer hub
Installing striking rod oil seal
Installing clutch housing dust seal
  1. 40 mm (1.57 in) dia  .
  2. 31 mm (1.22 in) dia  .
ST30621000
(J35869)
Drift
G04192417
 Installing differential side bearing outer race
[Use with ST30611000 (J25742-1).]
  1. 79 mm (3.11 in) dia  .
  2. 59 mm (2.32 in) dia  .
ST30611000
(J25742-1)
Drift handle
G04192418
 Installing differential side bearing outer race
[Use with ST30621000 (J35869).]
  1. 15 mm (0.59 in) 
  2. 335 mm (13.19 in) 
  3. 25 mm (0.98 in) dia  .
  4. M12 x 1.5P 
scientia non olet · About LEMON Manuals