LEMON Manuals: Even more car manuals for everyone
Home >> Nissan-Datsun >> 2004 >> Sentra SE-R >> Repair and Diagnosis >> External Pages >> Different car >> Section 1530 (Body, Lock & Security System) >> Power Door Lock System >> Back Door Key Cylinder Switch Check

Back Door Key Cylinder Switch Check

WARNING: This page is about a different car, the 2005 Nissan Xterra. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK BACK DOOR KEY CYLINDER SWITCH 

    With CONSULT-II

    Check back door key cylinder switch ("KEY CYL LK-SW") and ("KEY CYL UN-SW) in DATA MONITOR mode in CONSULT-II. Refer to "DATA MONITOR ".

    • When key inserted in back door key cylinder is turned to LOCK:

      KEY CYL LK-SW: ON 

    • When key inserted in back door key cylinder is turned to UNLOCK:

      KEY CYL UN-SW: ON 

      Fig 1: CONSULT-II Display - Data Monitor Mode
      G03609390Courtesy of NISSAN MOTOR CO., U.S.A.

    Without CONSULT-II

    Check voltage between BCM connector M18 terminals 7, 8 and ground.

    BCM CONNECTOR TERMINALS AND VOLTAGE REFERENCE

    Connector Terminals Condition Voltage (V) (Approx.)
    (+) (-)
    M18 7 Ground Neutral/Lock 5
    Unlock 0
    8 Neutral/Unlock 5
    Lock 0
    Fig 2: Checking Voltage Between BCM Connector M18 Terminals 7, 8 And Ground
    G03609391Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    • OK: Back door key cylinder switch signal is OK.
    • NG: GO TO 2.
  2. CHECK BACK DOOR KEY CYLINDER SWITCH 
    1. Turn ignition switch OFF.
    2. Disconnect back door key cylinder switch.
    3. Check continuity between back door key cylinder switch terminals 1, 2 and 3.
      BCM CONNECTOR TERMINALS AND CONTINUITY REFERENCE

      Terminals Condition Continuity
      1 - 2 Key is turned to LOCK. Yes
      Key is in N position or turned to UNLOCK No
      3 - 2 Key is turned to UNLOCK. Yes
      Key is in N position or turned to LOCK No

    OK or NG 

    • OK: GO TO 3.
    • NG: Replace back door key cylinder switch.
      Fig 3: Checking Continuity Between Back Door Key Cylinder Switch Terminals 1, 2 And 3
      G03609392Courtesy of NISSAN MOTOR CO., U.S.A.
  3. CHECK BACK DOOR KEY CYLINDER SWITCH HARNESS 
    1. Disconnect BCM.
    2. Check continuity between BCM connector M18 terminals 7, 8 and back door key cylinder switch connector D505 terminals 3, 1.

      7 - 3: Continuity should exist. 

      8 - 1: Continuity should exist. 

    3. Check continuity between BCM connector M18 terminals 7, 8 and ground.

      7 - Ground: Continuity should not exist. 

      8 - Ground: Continuity should not exist. 

    OK or NG 

    • OK: GO TO 4.
    • NG: Repair or replace harness
      Fig 4: Checking Continuity Between BCM Connector M18 Terminals 7, 8 And Back Door Key Cylinder Switch Connector D505 Terminals 3, 1
      G03609393Courtesy of NISSAN MOTOR CO., U.S.A.
  4. CHECK BACK DOOR KEY CYLINDER SWITCH GROUND 

    Check continuity between back door key cylinder switch connector D505 terminal 2 and ground.

    2 - Ground: Continuity should exist. 

    OK or NG 

    • OK: GO TO 5.
    • NG: Repair or replace harness
      Fig 5: Checking Continuity Between Back Door Key Cylinder Switch Connector D505 Terminal 2 And Ground
      G03609394Courtesy of NISSAN MOTOR CO., U.S.A.
  5. CHECK BCM OUTPUT VOLTAGE 
    1. Connect BCM.
    2. Check voltage between BCM connector M18 terminals 7, 8 and ground.

      7 - Ground: Approx. 5V 

      8 - Ground: Approx. 5V 

    OK or NG 

    • OK: Check condition of the harness and connector.
    • NG: Replace BCM. Refer to "REMOVAL AND INSTALLATION OF BCM ".
      Fig 6: Checking Voltage Between BCM Connector M18 Terminals 7, 8 And Ground
      G03609395Courtesy of NISSAN MOTOR CO., U.S.A.
scientia non olet · About LEMON Manuals